Downloaded from www.vandenborre.be
EN
13
Network connection
You can set up your TV so that it can access the
Internet through your local area network (LAN) using
a wired or wireless connection.
Connecting to a wired network
You can attach your TV to your LAN using cable in
three ways:
• You can attach your TV to your LAN by connecting
the LAN port on your TV to an external modem
using a Cat 5 cable.
• You can attach your TV to your LAN by connecting
the LAN port on your TV to an IP Sharer, which is
connected to an external modem. Use Cat 5 cable
for the connection.
• Depending on how your network is configured,
you may be able to attach your TV to your LAN by
connecting the LAN port on your TV directly to a
network wall outlet using a Cat 5 cable. Note that
the wall outlet is attached to a modem or router
elsewhere in your house.
Select
Smart TV > Settings > Interface
, then select
Ethernet
to connect to a wired network.
Connecting to a wireless network
To connect your TV to your network wirelessly, you
need a wireless router or modem and a Wireless
LAN Adapter. Connect your Wireless High-Gain USB
Adapter (USB dongle) delivered with your TV to your
TV’s
USB 1
port.
1.
Select
Smart TV > Settings > Interface
, then
select
Wireless
to connect to a wireless network.
2.
Select
Wireless setting
and press
OK/
► to enter.
3.
Connection Methods
: You can setup the wireless
network connection three ways.
-
Scan
• Select
Wireless setting
> Scan
, then press
OK/
►, the TV will scan all access points within
range. The access points found by the TV will
be displayed.
• Select an available access point, then press
OK/
► to connect the TV.
Notes:
- If you select a protected access point, you will
have to enter the corresponding password.
Press
OK
on the remote control to display the
virtual keyboard to enable you to enter the
password.
- This set has a memory function of available
access point, which enables your set to be
connected to the network even if you switch on
the TV after power off.
-
Manual
Select
Wireless setting
> Manual
, then press
OK/
►, you will be prompted to enter the correct
SSID of an available wireless router to set up the
If your AP supports WPS (Wi-Fi Protected
Setup), you can connect to the network via PIN
(Personal Identification Number) or PBC (Push
Button Configuration). WPS will automatically
configure the SSID and WPA key in either mode.
Generate a random PIN code. Make sure this
code is installed on the AP. (For the procedures,
refer to your router manual.) Press
: If your router has a PBC push button,
the PBC push button on your router within 2
minutes after you press
OK/
► again. Your TV
will automatically acquire all the network setting
values it needs and connect to your network.
Network setup
1.
Press
MENU
on the remote control and select
Smart TV > Settings > Internet connection
.
Press ◄/► to select
On
. Wait until the connection
is automatically established.
2.
Select
Smart TV > Settings > Connection test
,
then press
OK/
► to check the Internet connectivity.
If it does not work, follow below steps to make
sure of the connectivity.
3.
Select
Smart TV > Settings > IP setting
, then
press
OK/
► to enter the
IP setting
menu.
- Set
Address type
to
Auto
, it will acquire and
enter the needed IP address automatically.
- You can follow below steps to enter your IP
address manually.
• Set
Address type
to
Manual
, then press ▼ to
go to the first entry field.
• Enter the
IP address
,
Subnet mask
,
Default
gateway
,
Primary DNS
and
Secondary DNS
values. Use the alphanumeric buttons to enter
numbers and the arrow buttons to move from
one entry field to another.
- After setting, select
Smart TV > Settings
> Connection test
to check the Internet
connectivity again
.
4.
Select
Smart TV > Settings > Information
, then
press
OK/
► to display the information on current
connection, such as Interface, Address type, IP
address, etc.
Share & See
Note: This manual covers products with either
Share
& See
or
DLNA
function.
Share & See
is DLNA-
compatible.
Chapter 6
