JVC KD-DV5000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 30

background image

1-24 (No.49879)

Operation procedures

Press the [SEL], [POWER]
and [SOURCE] keys
simultaneously for 2 seconds.

Press the [SEL] key

"AREA/REGION" is
indicated on the LCD.

************
************
************

System control destination
DVD unit destination
DVD unit region

Press the [DISC UP] or [DISC DW] key

Press the [SEL] key

"VERSION" is
indicated on the LCD.

************
************
************
************

System control microcomputer version
Front end microcomputer version
Back end microcomputer version
DVD back end SDK version

Press the [SEL] key

"RUNNING MODE" is
indicated on the LCD.

Running mode: For use in running tests.

Press the [DISC UP] or [DISC DW] key

Press the [SEL] key

"CHECK MODE" is
indicated on the LCD.

DVD unit check mode
(See section "DVD check mode" for details.)

Press the [DISC UP] or [DISC DW] key

Press the [SEL] key

"EXPERT MODE" is
indicated on the LCD.

DVD unit expert mode

Press the [DISC UP] or [DISC DW] key

Press the [SEL] key

"TEMPERATURE" is
indicated on the LCD.

Thermistor's temperature data readout
: Data in the temperature sensor in the system control
is read every 5 seconds and displayed in hex numbers.

Press the [DISC UP] or [DISC DW] key

A

B

The unit enters the service mode.

Destination area/region display

Microcomputer version display

Press the [DISC UP] or [DISC DW] key

«
...
22
23
24
25
26
...
»

Содержание KD-DV5000































Отзывы:

Нет отзывов

Похожие инструкции для KD-DV5000

Бренд: Jensen Страницы: 66

Бренд: K1EL Страницы: 53

Бренд: Tivoli Audio Страницы: 16

Бренд: Xtrons Страницы: 12

Бренд: Streetwize Страницы: 5

Бренд: Eclipse Страницы: 141

Бренд: Pyle Страницы: 14

Бренд: Hallicrafters Страницы: 13

Бренд: Navico Страницы: 87

Бренд: Sound Storm Страницы: 11

Бренд: Domain Страницы: 14

Бренд: Domain Страницы: 15

Бренд: Boss Audio Systems Страницы: 13

Бренд: Phonocar Страницы: 8

KENWOOD KDC-BT278U

Бренд: JVCKENWOOD Страницы: 73

Бренд: Kobil Страницы: 3

Бренд: JVC Страницы: 2

DiMAX-ITC-System

Бренд: Massoth Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды