background image

(No.49879)1-17

3.2.9 Removing the DVD pickup assembly 

(See Fig.18 ~ 20)

• Prior to performing the following procedure, remove the front

end board.

(1) At the bottom of the body. turn the feed gear in the direction

of the arrow to move the DVD pickup outwards.

(2) Remove the screw 

F

 attaching the thrust spring.

(3) Remove the DVD pickup assembly upward on the L.S.gear

side and release from sub shaft at joint 

o

. Move the lead

screw of the DVD pickup assembly in the direction of the
arrow to release from joint 

p

.

Caution:

When releasing the lead screw at joint 

p

, the L.S.collar

comes off at the end of the lead screw. When reassem-
bling, reattach the L.S.collar to the lead screw and en-
gage joint 

p

.

Caution:

When reattaching the L.S.collar, reattach it to the point 

p

of the lead screw, and to the lod (M). Make sure that the
L.S.collar is set on the lod (M) spring.

(4) Remove the screw 

G

 attaching the rack spring/ rack plate

on the DVD pickup.

(5) Pull out the lead screw.

Caution:

Perform adjustment after replacing the pickup.

Fig.18

Fig.19

Fig.20

F

Feed gear

Thrust spring

DVD Pickup ass'y

O

P

L.S.Collar

Lod(M)

L.S.Gear

Lead screw

Sub shaft

DVD Pickup ass'y

G

Rack spring

Rack plate

L.S.Collar

DVD Pickup

Lead screw

L.S.Gear

Содержание KD-DV5000































Отзывы: