JVA JMB Series Скачать руководство пользователя

Страница: 14 / 64

Page 14

Specifica

tions

JVA JMB User Manual

SPECIFICATIONS

Specification Name

Value

Nominal Battery Voltage

14.3Vdc

Power consumption (maximum 46

stored joules)

3.9A at 13.5Vdc

1.9A at 24Vdc

Maximum voltage on control in

puts (Note 1)

12Vdc

Maximum power provided to “Si

ren” and “Strobe” outputs (Note 2)

35 Watts

Minimum Solar panel size (Note 3) 350W (6 hours sun)
Minimum Solar battery capacity

450 Ah (20% minimum over 4 days

without sun)

Table 2 - Electrical Specifications

Note 1

: The control inputs are powered with a weak internal pull up (5

volts at 0.2mA). The inputs are designed to be operated from voltage free

contacts (relays or switches) or switched voltage. If the switched voltage

method is used, the control voltages must not exceed 12V and a 1000 ohm

pull down resistor is required across the input.

Note 2

: The rated power is the combined output power of both the “Siren”

and “Strobe” outputs. The voltage which can be expected on this output is

the battery voltage. The combined maximum output current of both these

outputs is 2.5 Amps. Note that the maximum output power will drop as

battery voltage drops.

Note 3

: Please see our Solar Calculator here

https://www.jva-fence.com.au/solar.php

Содержание JMB Series

































































Результаты поиска

Содержание JMB Series

Отзывы:

Похожие инструкции для JMB Series

Бренды по названию

Популярные бренды

JVA JMB Series, Руководство пользователя

Результаты поиска

Содержание JMB Series

Отзывы:

Похожие инструкции для JMB Series

Бренды по названию

Популярные бренды