Juniper SRX1500 Скачать руководство пользователя страница 109

Страница: 109 / 168

Table 22: Alarms for Services Gateway Chassis Components

(continued)

Alarm Severity

Action

Alarm Conditions

Component

Yellow (minor)

•

Check the room
temperature. See

“SRX1500 Services
Gateway Environmental
Specifications” on
page 17

•

Check the air flow. See

“SRX1500 Services
Gateway Cabinet
Airflow Requirements”
on page 30

The services gateway
chassis temperature
is too warm.

Hardware
components on
services gateway

Red (major)

Place your hand near the
exhaust vents at the rear
of the chassis to determine
whether the fan is pushing
air out of the chassis.

The services gateway
fan has failed.

NOTE:

For more information about alarms, see the appropriate Junos OS

Monitoring and Troubleshooting for Security Devices Guide.

Documentation

Troubleshooting Resources for the SRX1500 Services Gateway Overview on page 89

•

Troubleshooting the Power System on the SRX1500 Services Gateway on page 91

•

Using the RESET CONFIG Button on the SRX1500 Services Gateway on page 94

•

Changing the RESET CONFIG Button Behavior on the SRX1500 Services Gateway on
page 94

Troubleshooting the Power System on the SRX1500 Services Gateway

Problem

Description:

The LEDs on the services gateway enable you to determine the performance

and operation of the power system. The PWR LED located on the front panel of the
services gateway, as described in

Table 23 on page 92

, indicates the different status

settings with respect to the power system.

Chapter 19: Troubleshooting Components

Содержание SRX1500
















































































































































Результаты поиска

Содержание SRX1500

Отзывы:

Похожие инструкции для SRX1500

Бренды по названию

Популярные бренды

Juniper SRX1500, Руководство по оборудованию

Результаты поиска

Содержание SRX1500

Отзывы:

Похожие инструкции для SRX1500

Бренды по названию

Популярные бренды