Juniper MX2010 Скачать руководство пользователя страница 70

Страница: 70 / 825

CHAPTER 5

Cooling System

IN THIS CHAPTER

MX2010 Cooling System Description | 45

MX2010 Fan Tray LED | 48

MX2010 Cooling System Description

The cooling system consists of the following components:

•

Fan tray—MX2000-FANTRAY

•

Lower fan tray air filter—MX2010-FLTR-KIT-S

•

Air baffle—MX2000-UPR-BAFFLE

The cooling system components work together to keep all router components within the acceptable

temperature range. The router has four fan trays, two trays located at the top, and two trays located at

the bottom of the router that install horizontally. Each fan tray contains six fans and are 172 mm in diameter.

The fan trays are interchangeable and are hot-insertable and hot-removable.

Each fan tray has a double safety latch, so the fan tray cannot be removed in one swift motion (see

Figure 17 on page 46

). To remove the fan tray, press and hold the latch until LED turns off. The secondary

latch will engage during removal. Press the secondary latch to fully remove the fan tray.

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды