Juniper MX2010 Скачать руководство пользователя страница 286

Страница: 286 / 825

Figure 109: Pulling the MX2010 into the Rack

g000068

NOTE:

A four-person team is needed to carefully guide the router into the rack while

operating the winch.

NOTE:

If the router is not pulled all the way into the rack by the winch mechanism, grasp

the handles on the shipping covers and carefully slide the router onto the mounting shelf

until the front-mounting flanges contact the rack rails. You must remove the winch bracket

to perform this procedure.

NOTE:

There must be a minimum of 45-U of usable rack space when installing the MX2010

into a 45-U rack.

11. Remove the router transport platform, and set the platform aside.

269

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды