background image

  Capacity:  2100 W (maximum 2500 W)

  DC output: 333.12 W (Lower Zone, 6.50 A at 51.25 V, 15.86% of capacity)

PSM 8:

  State:     Online

  DC input:  OK (INP1 feed expected, INP1 feed connected)

  Capacity:  2100 W (maximum 2500 W)

  DC output: 333.12 W (Lower Zone, 6.50 A at 51.25 V, 15.86% of capacity)

PSM 9:

  State:     Empty

  Input:     Absent

PSM 10:

  State:     Empty

  Input:     Absent

PSM 11:

  State:     Empty

  Input:     Absent

PSM 12:

  State:     Empty

  Input:     Absent

PSM 13:

  State:     Online

  DC input:  OK (INP1 feed expected, INP1 feed connected)

  Capacity:  2100 W (maximum 2500 W)

  DC output: 269.06 W (Upper Zone, 5.25 A at 51.25 V, 12.81% of capacity)

PSM 14:

  State:     Online

  DC input:  OK (INP1 feed expected, INP1 feed connected)

  Capacity:  2100 W (maximum 2500 W)

  DC output: 281.88 W (Upper Zone, 5.50 A at 51.25 V, 13.42% of capacity)

PSM 15:

  State:     Online

  DC input:  OK (INP1 feed expected, INP1 feed connected)

  Capacity:  2100 W (maximum 2500 W)

  DC output: 269.06 W (Upper Zone, 5.25 A at 51.25 V, 12.81% of capacity)

PSM 16:

677

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы: