Juniper MX2010 Скачать руководство пользователя страница 609

Страница: 609 / 825

Figure 311: Disconnecting the Power Cord from a Three-Phase Wye AC Power Distribution Module

g007082

To remove wires from the terminal block that serves three PSMs:

a. Remove the wire labeled N from the input terminal labeled N2.

b. Remove the wire labeled L3 from the input terminal labeled C2.

c. Remove the wire labeled L2 from the input terminal labeled B2.

d. Remove the wire labeled L1 from the input terminal labeled A2.

e. Remove the grounding wire from the grounding point labeled GND.

NOTE:

The three-phase wye AC PDM terminal blocks will be flipped depending on which

slot the PDM gets plugged in to.

NOTE:

The terminal connections have either slotted screws or hex screws. Use a 1/4-in.

slotted screwdriver for the slotted screws. Use a 5/32-in. (4 mm) Allen wrench for the

5/16-in. hex screws.

593

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды