Juniper MX2010 Скачать руководство пользователя страница 291

Страница: 291 / 825

Figure 112: Sliding the MX2010 into the Open-Frame Rack

g000069

NOTE:

A four-person team is needed to carefully guide the router into the rack.

NOTE:

There must be a minimum of 45-U of usable rack space when installing the MX2010

into a 45-U rack.

9. Remove the router transport platform, and set the platform aside.

10. Insert twelve mounting screws (six on each side) into the mounting holes to secure the router to the

rack.

11. Visually inspect the alignment of the router. To verify that the router is installed properly in the rack,

see that all the mounting screws on one side of the rack are aligned with the mounting screws on the

opposite side and the router is level.

12. Reassemble the router transport kit, and set aside.

274

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды