Jungheinrich KMS 100, Руководство по эксплуатации

Страница: 57 / 67

1298
.GB
F 6
j) Chain to be first checked after approx. 100 operating hours; tighten, if necessary.
e) IG: induction-guided trucks
Maintenance intervals
Standard =
t
W M M M
1 3 6 12
Lifting device 10.1 Apply grease to rollers and side run areas of idler pulleys
in the hoist frame profiles.
t
10.2 Check secure attachment of hoist frame
t
10.3 Check hoisting chains and chain guide for wear; adjust
and grease j)
t
10.4 Visual check of rollers, slide pieces and stops
t
10.5 Check hoisting frame seatings
t
10.7 Check fork tines and fork carrier for wear and damage
t
10.8 Lubricate lubricating points of the chain rollers
t
Attachments: 11.1 Check function
t
11.2 Check secure attachment at the device and supporting
elements
t
11.3 Check seatings, guides and stops for wear and damage;
apply grease
t
Lubrication
service: 12.1 Grease truck according to lubrication plan
t
General mea-
surements: 13.1 Check electrical system for short to ground
t
13.2 Check driving speed and braking distance
t
13.3 Check lifting and lowering speed
t
13.4 Check safety facilities and switch-off devices
t
13.5 IG: Check amperage of guide wire; re-adjust,
if necessary e)
t
13.6 Check driving behavior on IG wire and maximum devia-
tion; re-adjust, if necessary e)
t
13.7 Check track-in and driving behaviour on the IG wire
during aisle track-in e)
t
13.8 Check IG emergency STOP function e)
t
Demonstrati-
on: 14.1 Perform a trial run under a nominal load
t
14.2 Upon completion of servicing operations, demonstrate
the truck to the person responsible
t
1298
.GB
F 6
j) Chain to be first checked after approx. 100 operating hours; tighten, if necessary.
e) IG: induction-guided trucks
Maintenance intervals
Standard =
t
W M M M
1 3 6 12
Lifting device 10.1 Apply grease to rollers and side run areas of idler pulleys
in the hoist frame profiles.
t
10.2 Check secure attachment of hoist frame
t
10.3 Check hoisting chains and chain guide for wear; adjust
and grease j)
t
10.4 Visual check of rollers, slide pieces and stops
t
10.5 Check hoisting frame seatings
t
10.7 Check fork tines and fork carrier for wear and damage
t
10.8 Lubricate lubricating points of the chain rollers
t
Attachments: 11.1 Check function
t
11.2 Check secure attachment at the device and supporting
elements
t
11.3 Check seatings, guides and stops for wear and damage;
apply grease
t
Lubrication
service: 12.1 Grease truck according to lubrication plan
t
General mea-
surements: 13.1 Check electrical system for short to ground
t
13.2 Check driving speed and braking distance
t
13.3 Check lifting and lowering speed
t
13.4 Check safety facilities and switch-off devices
t
13.5 IG: Check amperage of guide wire; re-adjust,
if necessary e)
t
13.6 Check driving behavior on IG wire and maximum devia-
tion; re-adjust, if necessary e)
t
13.7 Check track-in and driving behaviour on the IG wire
during aisle track-in e)
t
13.8 Check IG emergency STOP function e)
t
Demonstrati-
on: 14.1 Perform a trial run under a nominal load
t
14.2 Upon completion of servicing operations, demonstrate
the truck to the person responsible
t