Jungheinrich EJB 14, Руководство по эксплуатации

Страница: 38 / 49

F 1
099
9.G
B
F Maintenance of the truck
1 Operational safety and protection of the environment
The checks and maintenance work listed in this chapter have to be performed accor-
ding to the intervals of the maintenance checklists.
f
Modifications of truck assemblies, especially of the safety installations, are not per-
mitted. On no account must the operational speeds of the truck be changed.
m
Only original spare parts have been passed by our quality assurance service. In order
to ensure safe and reliable operation only original spare parts of the manufacturer
must be used. Old parts and changed consumption type materials must be disposed
of in accordance with the applicable environmental protection regulations. The Oil
Change Service of the manufacturer is available for oil changes.
Upon completion of any checks and servicing activities, the operations contained in
the section "Recommissioning" must be performed (see section 6.8).
2 Safety regulations for repair
Servicing and maintenance personnel: Maintenance and repair of the floor con-
veyors may only be performed by expert personnel of the manufacturer. The Service
Organisation of the manufacturer has service engineers available that have been
specifically trained for these tasks. We therefore advise to conclude a maintenance
contract with the manufacturer’s Service Base responsible for the area.
Lifting and jacking up: When a fork-lift truck is to be lifted, the lifting gear must only
be secured to the points specially provided for this purpose. When the truck is to be
jacked up, suitable measures must be taken to prevent the truck from slipping or tip-
ping over (use of chocks, wooden blocks). Work underneath raised forks must only
be carried out, when the fork is immobilised and supported by a chain of adequate
strength.
Cleaning operations: No inflammable liquids must be used when cleaning the indu-
strial truck. Prior to performing cleaning operations all appropriate safety measures
must be taken to avoid sparking (e.g. due to short circuits). The battery connector
must be disconnected. Electric and electronic components must be cleaned with low-
pressure air or suction air and a non-conducting, antistatic brush.
m
If the truck is to be cleaned using water or a steam jet, all electric and electronic as-
semblies have to be carefully covered beforehand, as humidity will cause mal-
functions.
Steam-cleaning is not permitted.
Upon the completion of cleaning work the operations detailed in section “Recommis-
sioning” have to be performed.
F 1
099
9.G
B
F Maintenance of the truck
1 Operational safety and protection of the environment
The checks and maintenance work listed in this chapter have to be performed accor-
ding to the intervals of the maintenance checklists.
f
Modifications of truck assemblies, especially of the safety installations, are not per-
mitted. On no account must the operational speeds of the truck be changed.
m
Only original spare parts have been passed by our quality assurance service. In order
to ensure safe and reliable operation only original spare parts of the manufacturer
must be used. Old parts and changed consumption type materials must be disposed
of in accordance with the applicable environmental protection regulations. The Oil
Change Service of the manufacturer is available for oil changes.
Upon completion of any checks and servicing activities, the operations contained in
the section "Recommissioning" must be performed (see section 6.8).
2 Safety regulations for repair
Servicing and maintenance personnel: Maintenance and repair of the floor con-
veyors may only be performed by expert personnel of the manufacturer. The Service
Organisation of the manufacturer has service engineers available that have been
specifically trained for these tasks. We therefore advise to conclude a maintenance
contract with the manufacturer’s Service Base responsible for the area.
Lifting and jacking up: When a fork-lift truck is to be lifted, the lifting gear must only
be secured to the points specially provided for this purpose. When the truck is to be
jacked up, suitable measures must be taken to prevent the truck from slipping or tip-
ping over (use of chocks, wooden blocks). Work underneath raised forks must only
be carried out, when the fork is immobilised and supported by a chain of adequate
strength.
Cleaning operations: No inflammable liquids must be used when cleaning the indu-
strial truck. Prior to performing cleaning operations all appropriate safety measures
must be taken to avoid sparking (e.g. due to short circuits). The battery connector
must be disconnected. Electric and electronic components must be cleaned with low-
pressure air or suction air and a non-conducting, antistatic brush.
m
If the truck is to be cleaned using water or a steam jet, all electric and electronic as-
semblies have to be carefully covered beforehand, as humidity will cause mal-
functions.
Steam-cleaning is not permitted.
Upon the completion of cleaning work the operations detailed in section “Recommis-
sioning” have to be performed.