background image

Test operation is switched on for 5 minutes, afterwards the motion detector switches to 
automatic operation again. 

Function 

Value 

Sensitivity 

100 % 

Detection area 

180 ° 

Brightness threshold 

Day mode 

run-on time 

1 second 

By pressing the 

À

 button, you can switch to automatic operation at any time. 

Performing a reset 

During a reset, the motion detector is reset to the factory settings. 

Press the 

Ú

 button for longer than 10 seconds. 

Function 

Value 

Sensitivity 

100 % 

Detection angle 

180 ° 

Brightness threshold 

10 lux 

run-on time 

30 seconds 

Operating location 

Indoors 

Night light function 

Switched-off 

Presence simulation 

Switched-off 

If the 

Ú

 button is pressed for less than 10 seconds, only a few functions are 

terminated (see chapter 4. Operation on a main unit). 

5 Operation on a 3-wire extension insert 

Only a few settings are possible in combination with a 3-wire extension insert. 

Setting sensitivity (see Chapter Operation on a main unit) 

Use outdoors (see Chapter Operation on a main unit) 

Extension Off for 2 hours or Continuous off 

3-wire extension insert Off for 2 hours 

Press 

Ã

 button of the IR remote control. 

Extension is switched off for 2 hours. The extension is in automatic operation again after 
the time has elapsed. 

By pressing the 

À

 button of the IR remote control, you can switch to automatic 

operation at any time. 

3-wire extension insert Continuous off 

Press 

Á

 button of the IR remote control, alternatively press button (5) on the 

motion sensor. 
Extension is switched off continuously. The red LED lights up. 

By pressing the 

À

 button of the IR remote control, alternative button (5) on the motion 

detector, you can switch to automatic operation at any time. 

8/13 

32576803 
J:0082576803 

03.05.2011 

Light Management  

Universal automatic switch 180° 2.20 m 

Содержание AS 1280-1 Series














Отзывы: