Jun-Air 87R-4P Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 23

background image

2

6190900 (Rev B)

87R-4P Compressor System User Guide

© 2017, JUN-AIR

We reserve the right to make any alterations which may be due to any technical improvements

Printed in the USA

Section

Page Number

Declaration of Conformity

3

Table of Symbols

4

System Features

5

Installation and Operation

7

Maintenance

11

Troubleshooting

21

Warranty Policy

22

WARNING

PLEASE READ THIS MANUAL COMPLETELY BEFORE INSTALLING AND USING

THIS PRODUCT. SAVE THIS MANUAL FOR FUTURE REFERENCE AND

KEEP IN THE VICINITY OF THE PRODUCT.

Dear Customer:
Congratulations on the purchase of your new JUN-AIR Industrial Compressed Air System.
This system’s intended purpose is for industrial and laboratory compression applications. It is to be used in

accordance with UL1450/CSA 22.2 standards, along with all applicable codes. The system utilizes an oil-less

rocking piston compressor that produces clean, dry, oil-free pressurized air flow when connected to an indus-

trial or laboratory device. The tank ensures that a constant supply of air is available to the device.
A pressure regulator and safety relief valve are also included to ensure safe operation of the system. This

manual provides installation, operation and preventative maintenance guidelines that should be followed to

ensure correct/reliable performance of this system.
Please carry out all maintenance according to relevant instructions.

«
1
2
3
4
...
»

Содержание 87R-4P
























Отзывы:

Нет отзывов

Похожие инструкции для 87R-4P

Бренд: Parkside Страницы: 47

Бренд: Brooks Страницы: 56

Бренд: Ariel Страницы: 141

Бренд: Denyo Страницы: 67

Бренд: Gardner Denver Страницы: 20

Бренд: Campbell Hausfeld Страницы: 57

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: California Air Tools Страницы: 18

Бренд: Kobalt Страницы: 8

TOPS - Thermal Overload Protection System

Бренд: Kobalt Страницы: 28

Бренд: Kobalt Страницы: 24

Бренд: Kobalt Страницы: 24

Бренд: MasterCraft Страницы: 25

SBBHS030020SD10

Бренд: Powerex Страницы: 12

Бренд: Sharper Image Страницы: 4

Бренд: L&W Compressors Страницы: 155

Бренд: FScurtis Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды