Jun-Air 87R-4P Скачать руководство пользователя страница 12

Страница: 12 / 23

6190900 (Rev B)

87R-4P Compressor System User Guide

We reserve the right to make any alterations which may be due to any technical improvements

Printed in the USA

Cleaning or Replacing the System-Intake

Filter Element

1. Turn the system off and disconnect it from electrical

power.

2. Remove the intake filter element from the system cover

and inspect for damage.

3. If cleaning the filter, use warm, soapy water and ensure

that it is dry before reinstalling. If replacing the filter,
discard the used element.

4. Install the new or cleaned filter element into the system

cover, ensuring that it is fully seated the cover.

5. Reconnect electrical power to the system.

NOTE:

Filter kits are available for the system (see PARTS

AND ACCESSORIES).

Replacing the Autodrain-Filter Element

1. Turn the system off and disconnect it from electrical

power.

2. Bleed all of the air from the system.
3. Remove the handle bolts (4) and loosen the cover

screws (4) to tilt the cover forward.

4. Rotate the filter bowl and drop it down slightly to re-

move it, using caution to avoid damaging or kinking the
drain tube.

5. Remove the filter element by turning it completely out,

using caution to avoid damaging the plastic element
holder. Discard the used filter.

6. Install a new 5

m filter element after verifying that it is

the correct part.

7. Position the filter bowl by pushing up slightly and rotat-

ing it into place. Verify that the drain tube is not kinked
or damaged.

8. Ensure that the drain tube passes through the base

plate and into the evaporator tray.

9. Replace the cover and reinstall the handle bolts and

cover screws.

10. Reconnect the electrical power to the system.

Replacing the Evaporator-Tray Element

1. Turn the system off and disconnect it from electrical

power.

2. Remove the handle bolts (4) and loosen the cover

screws (4) to tip the cover forward.

3. Locate the evaporator tray and remove the foam.
4. Discard the used foam, clean the tray, and install new

foam.

5. Replace the cover and reinstall the handle bolts and

cover screws.

6. Reconnect the system to electrical power.

Replacing the Compressor-Intake Filter

Element

1. Turn the system off and disconnect it from electrical

power.

2. Remove the handle bolts (4) and loosen the cover

screws (4) to tip the cover forward.

3. Remove the intake filter cap by depressing and rotating

it while holding the base of the filter.

4. Remove and discard the used intake filter element.
5. Install a replacement filter element and reinstall the

filter cap.

6. Replace the cover and reinstall the handle bolts and

cover screws.

7. Reconnect the system to electrical power.

WARNING

Disposal of system components, deemed non-usable by

the authorized dealer and the end user, should be done in

accordance with all local codes. Contact your local waste

management authorities to determine proper disposal

methods.

WARNING

Do not exceed the OSHA requirements of 2 bar [29 psig] air

for cleaning purposes.

Содержание 87R-4P
























Результаты поиска

Содержание 87R-4P

Отзывы:

Похожие инструкции для 87R-4P

Бренды по названию

Популярные бренды

Jun-Air 87R-4P, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 87R-4P

Отзывы:

Похожие инструкции для 87R-4P

Бренды по названию

Популярные бренды