manualshive.com logo in svg

JUMO 202710, Руководство по эксплуатации, Страница: 24 / 32

Поделиться
Скачать
JUMO 202710 Скачать руководство пользователя страница 24

24

6 Error and system messages

Error or 
system 
message

Cause

Remedy

General:

Low battery voltage. 
Functionality can only be ensured 
for a short time.

Fit a new battery.

Low battery voltage.
Operating from electrical supply: 
wrong voltage.

Fit a new battery.
Check power supply and replace if 
necessary.
If the error persists, then the hand-held meter 
is faulty.

No display
or
crazy 
characters

Low battery voltage.
Operating from electrical supply: 
power supply is faulty or wrong 
voltage/polarity.
Instrument error or fault.

Fit a new battery.
Check power supply and replace if 
necessary.
Remove battery or power supply – wait for 5 
seconds – reconnect.
If the error persists, then the hand-held meter 
is faulty.

Gone beyond the measurement 
range. Defect in combination 
electrode, temperature sensor or 
connecting cable.

Check combination electrode, temperature 
sensor and connecting cable, and replace if 
necessary.

Gone below measurement range.
Defect in combination electrode, 
temperature sensor or cable.

Check combination electrode, temperature 
sensor and connecting cable, and replace if 
necessary.

Instrument error.

Switch off the hand-held meter, and switch
on again after 5 seconds.
If the error persists, then the hand-held meter 
is faulty.

Only for temperature measurement (thEr)

No temperature sensor 
connected.
Temperature sensor is faulty.

Connect/replace the temperature sensor.

Value could not be
calculated.

Outside the permissible temperature
compensation range (0 to 105°C) or outside 
the permissible measurement range (Err.1 or 
Err.2). 

Only for pH measurement:

Содержание 202710

































Отзывы:

Нет отзывов