JUMO 202560 Скачать руководство пользователя страница 83

Страница: 83 / 104

10 Eliminating faults and malfunctions

10.1 Possible faults

Problem

Possible cause

Measures

No measurement display
or
current output

Supply voltage
missing

Check supply voltage,
also check terminals

Measurement display
000 or
analog output 0/4 mA
or 0 V

Sensor not immersed in
medium; reservoir level
too low

Top up the reservoir

Flow-through fitting
is blocked

Clean flow-through
fitting

Sensor is faulty

Replace the sensor

Wrong or
unstable
measurement display

Sensor not immersed
deeply enough

Top up the reservoir

Inadequate mixing

Ensure good mixing;
for sensor: all-round
free space of approx.
5 mm to ensure all-round
flow

Air bubbles

Check mounting site

Measurement display
8888,
Temperature display
“ok”, blinking

Overrange / underrange
or faulty sensor

Check the basic settings.

Check the electrical
connection for the
sensor.

Replace the instrument.

Measurement display
8888,
temperature display
8888, blinking

Infringement of
temperature range (over/
underrange), or short-
circuit or cable break for
the temperature sensor

The temperature for the
measured medium is
outside the permissible
range for temperature
compensation.

Replace the instrument.

Replace the sensor.

Temperature display and
measurement display are
normal,
but the unit indicates
????

The basic settings were
configured on the
instrument in the
“Customized” mode.

“Unit” must be
configured through the
setup program, or
the “Customized” mode
must be abandoned.

Fluctuating
measurement display

Symmetrical
connection was chosen.

- Interruption of

connection to
liquid potential.

- Interference potential

too high.

- Check the electrical

connection, see
Chapter 4.5 “Terminal
assignments”, page
19

- Eliminate interference

potential.

All manuals and user guides at all-guides.com

Содержание 202560









































































































Результаты поиска

Содержание 202560

Отзывы:

Бренды по названию

Популярные бренды

JUMO 202560, Руководство по эксплуатации

Результаты поиска

Содержание 202560

Отзывы:

Бренды по названию

Популярные бренды