JUMO 202560 Скачать руководство пользователя страница 36

Страница: 36 / 104

6 Operation

6.6.3

Simulation of analog outputs via MANUAL mode

Enabling and
activation

✱

Select activation of simulation of the actual value output:
Administrator level / Password / Parameter level / Analog output 1 or 2 /
Simulation / Off or On.

With "On" the output takes on the value of the "Simulation value" parameter.

When the JUMO AQUIS is in display mode, the word MANUAL appears in the
status line of the display.

Deactivation

✱

Administrator level / Password / Parameter level / Analog output 1 or 2 /
Simulation / Off.

The corresponding output of the JUMO AQUIS 500 works again.

When the JUMO AQUIS is in display mode, the word MANUAL disappears
from the status line of the display.

6.6.4

MANUAL/Simulation overview

You can display which outputs and/or controllers are in MANUAL mode.
The instrument is in "normal display" mode

Press the

key several times for less than 2 seconds (the number of times

varies depending on the equipment and configuration of the instrument).

PGM

To return to measuring mode:
press the

key or wait for a "timeout".

EXIT

All manuals and user guides at all-guides.com

all-guides.com

Содержание 202560









































































































Результаты поиска

Содержание 202560

Отзывы:

Бренды по названию

Популярные бренды

JUMO 202560, Руководство по эксплуатации

Результаты поиска

Содержание 202560

Отзывы:

Бренды по названию

Популярные бренды