JUMO 202560 Скачать руководство пользователя страница 44

Страница: 44 / 104

6 Operation

6.9.6

Enable calibration

Here you can decide whether to enable the parameter for alteration
(calibration) or not.

1-POINT CALIB.
2-POINT CALIB.
3-POINT CALIB.

6.9.7

Delete logbook

REALLY DELETE LOGBOOK?

YES / NO

6.10 Device info

The present configuration for all important parameters is shown here,
e.g.
SENSOR

-> PH STANDARD

MONIT. REF.

-> OFF

MONIT. GLASS EL.

-> OFF

6.11 Controller function

Simple
switching
functions

In the JUMO AQUIS 500, simple switching functions, such as alarm contacts
and limit comparators or the signal from the calibration timer, are configured at
the parameter level, through the parameters for “Switching output 1 or 2”.

The parameters for the controller channel 1 or 2 respectively must then be set
to “Off”.

Higher-level
control
functions

Higher-level control functions are configured at the parameter level, through
the parameters for “Controller channel 1 or 2”.

The parameters for the controller channels must then be set to “Controller 1 or
2”.

All manuals and user guides at all-guides.com

Содержание 202560









































































































Результаты поиска

Содержание 202560

Отзывы:

Бренды по названию

Популярные бренды

JUMO 202560, Руководство по эксплуатации

Результаты поиска

Содержание 202560

Отзывы:

Бренды по названию

Популярные бренды