JUKI DP-2100 Скачать руководство пользователя страница 182

Страница: 182 / 187

−

176

−

24-6 Greasing parts

Periodically perform grease-up every 6 months as a standard .

For the grease, use the exclusive grease (Part No. : 40006323) supplied as accessories.

In addition, for the places to be greased, refer to the Engineer's Manual for DP-2100.

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the
sewing machine.

1. When they are not in parallel,

remaining of thread end will be

caused.

2. When the knife pressure is low,

thread trimming failure will be

caused. When it is excessively high,

it is related to the damage of the

blade point of counter knife.

(4) Adjusting the position of the moving knife and the counter knife

Install moving knife

by making it come in contact with the moving knife base.

Install counter knife

together with knife pressure adjustment plate

Loosen counter knife setscrew

, adjust so that

moving knife eyeend blade section

and counter

knife blade section

come in contact with each

other in parallel, slightly press knife pressure

adjustment plate

in the direction

, and tighten

with the setscrew.

Содержание DP-2100




























































































































































































Результаты поиска

Содержание DP-2100

Отзывы:

JUKI DP-2100, Инструкция по эксплуатации, Страница: 182 / 187

Результаты поиска

Содержание DP-2100

Отзывы: