manualshive.com logo in svg

JUKI DP-2100, Инструкция по эксплуатации, Страница: 140 / 187

Поделиться
Скачать
JUKI DP-2100 Скачать руководство пользователя страница 140

−

 134 

−

[ Performing format ]

In case of re-formating the smart media, be sure to perform it with IP-200. The smart media formated with the

personal computer cannot be read with IP-200.

3

1)

Display the smart media format screen.

When

 

 

1 

switch is held pressed for three

seconds, smart media format button 

 

2

 is

displayed on the screen. When this button is

pressed, the smart media format screen is

displayed.

2)

Start formating of the smart media.

Set the smart media you desire to format to the

smart media slot, close the cover, press ENTER

button 

 

3 

and formating starts.

Save necessary data in the smart

media to the other vehicle before

f o r m a t i n g .   W h e n   f o r m a t i n g   i s

performed, the inside data are deleted.

[ Prohibition items in handling the smart media ]

1

Smart media is a precision electronic instrument. Do not bend it or apply shock to it.

2

It is recommended to periodically save the data saved in the smart media to the other vehicle to prepare

for accidents.

3

When initializing the data, perform it after checking that necessary data do not exist in the card.

4

Avoid using or storing the smart media in a place of high temperature and high humidity.

5

Avoid using the smart media near exothermic and combustible articles.

6

If the contact part of the card becomes dirty, failure of contact will be caused. Do not touch by hand, and

control so that dust, oil, or other foreign material does not adhere to it. In addition, the inside element is

damaged by static electricity or the like. So, be very careful when handling.

7

Smart media has a span of life. Writing and deletion cannot be performed after an extended period of

use. In this case, replace it with a new one.

2

1

Содержание DP-2100




























































































































































































Отзывы:

Нет отзывов