JUKI DP-2100 Скачать руководство пользователя страница 178

Страница: 178 / 187

−

172

−

24-3 Adjusting the height of the walking foot and the presser foot

Be careful of parallel

(2) Adjusting the height of presser foot

1) Bring the needle bar to its lower dead point.

2) Remove face plate

3) Loosen presser foot bar bracket clamp screw

4) Move upward presser foot

in the range of 0.1 to 0.5 mm and tighten screw

1. Clearance between top and bottom

feed belts (dimension A) is 0.1 to

1.0 mm. If the clearance is more

than the specified dimension,

components come in contact with

each other.

2. When tightening screw

, be

careful of the parallel of walking foot

and presser foot

. Bend of

material or feed trouble will be

caused.

Bring the needle bar to its upper dead point.

Remove stopper plug

Insert a hexagonal wrench key into the hole from

which the stopper plug has been removed, and

loosen walking foot bar bracket clamp screw

Move walking foot

up or down in the range of

0.1 to 1.0 mm and tighten screw

(1) Adjusting the height of walking foot

When the clearance becomes larger

than the specified value, feed force is

deteriorated. So, be careful.

1. Clearance between the bottom surface of presser foot and the needle hole guide has

been factory-adjusted to 0.1 mm at the time of delivery.

2. When the clearance becomes larger than the specified value, feed force is deteriorated.

So, be careful.

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the
sewing machine.

Содержание DP-2100




























































































































































































Результаты поиска

Содержание DP-2100

Отзывы:

Похожие инструкции для DP-2100

Бренды по названию

Популярные бренды

JUKI DP-2100, Инструкция по эксплуатации

Результаты поиска

Содержание DP-2100

Отзывы:

Похожие инструкции для DP-2100

Бренды по названию

Популярные бренды