JRC JLR-21 Скачать руководство пользователя страница 91

Страница: 91 / 164

5-27

•

RMC MAG CORR:

You can select automatic or manual magnetic correction.

When you select automatic, correction is automatically calculated for

the correction value from the GPS position and output the data
(except sensor through port in Data IN/OUT 1 connector).

When you select manual, correction is performed using a manually

entered value.

•

5Hz DISPLAY:

Turning ON will change a display-updating cycle for the

Latitude/Longitude, SOG, and COG displays to every 5Hz (200msec).

Turning OFF will change a display-updating cycle back to the normal

setting of every 1 sec.

However, the updating cycle of the Latitude/Longitude, SOG, and

COG output data for external devices is set in Data I/O Menu

regardless of this setting. (Refer to 5.3.7 Data I/O Settings

(DATA I/O) for details.)

•

SOG BAR RANGE :

Set the maximum value for the SOG bar range from the following.

Applicable to the Compass screens E and F, and the Trend Graph

screen.

•

Press to return to the system settings.

•

Settings can be changed in Maintenance Mode (Press and hold both and for about

3 seconds to go to the mode.)

●

Plot interval of the trend graph

The display range of X-axis (time axis) in the trend graph can be changed by the

▲

▼

keys. (Select from 1 min, 5 min, 30 min, 1 hr, 3 hrs, 5 hrs, or 12 hrs.)

  The plot interval of each display range is shown in the following table.    The longer the display
  range, the longer the plot interval, and a change in the period of time shorter than this interval is
  not displayed (plotted.)

<Plot

Interval>

Display range of
X-axis

1min. 5min.

30min.

1hour. 3hour. 5hour. 12hour.

Plot interval

every

1sec.

every

4sec.

every

24sec.

every

48sec.

every

144sec.

every

240sec.

every

576sec.

Average

The average in each plot interval

Maximum

The maximum of the absolute value in each plot interval

Unit of measure configured in
SPEED UNIT in the SYSTEM
menu

Available range

kn 5,10,15,20,25,30,50,100

km/h 9,19,28,37,46,56,93,185

mi/h 6,12,17,23,29,35,58,115

SOG bar range is set to this
axis (vertical axis) on this
screen. (Compass F screen)

Memo

Содержание JLR-21





































































































































































Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды

JRC JLR-21, Инструкция по эксплуатации

Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды