JRC JLR-21 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 164

background image

2-22

●

Cable Length

■

For cable lengths of less than 30 m

Use the option cable (CFQ-7249).

< Waterproofing method for connectors of extended line >

Display side

<Start of Self-bonding tape

wrapping>

Connector (Plug) or Tube

<End of Self-bonding tape

wrapping>

Sensor side

Self-bonding tape

Take a proper length of tape off the role.
While pulling in accordance with tape
manual, wrap it around the connector
with one half of it overlapped so that the
wrapped tape may form

three layers

.

However, portions between the
connector and cable have different
diameters. This portion apply tape more
than the other portions.
When the tape has been wrapped, press
to hold by hand.

Protective PVC tape (vinyl tape)

Taking care not to give tension to the
tape,
wrap the tape around the connector with
one
half of it overlapped so that the wrapped
tape
may form

three layers

.

<End of vinyl tape

wrapping>

10mm or more

<Start of vinyl tape

wrapping>

25mm or more

25mm or more

10mm or more

Connector (Socket) or Tube

Connector (Plug)

Connector (Socket)

CFQ-7249 / 20m

(CFQ7249-10 / 10m)

Approx.

Φ

22.2mm

Approx.

Φ

7mm

Approx.

Φ

20.2mm

Female

Female

Male

Female

* A connector with pins is male side.

CFQ-7248(10m)
(Attachment)

Sensor side

Display
side

Waterproof treatment is required.
Refer to <Waterproofing method for connectors of extended line>
on the next section, please waterproof treatment.

«
...
38
39
40
41
42
...
»

Содержание JLR-21





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JLR-21

Бренд: eMoMo Страницы: 2

Бренд: Alto Страницы: 60

Compact FLASH III

Бренд: ACS Страницы: 37

Бренд: Sound Devices Страницы: 20

Бренд: Pioneer Страницы: 2

Бренд: Pioneer Страницы: 9

Бренд: Pioneer Страницы: 96

Бренд: Panasonic Страницы: 70

Бренд: Panasonic Страницы: 74

Бренд: Panasonic Страницы: 125

Бренд: Panasonic Страницы: 132

Бренд: Panasonic Страницы: 139

Бренд: Panasonic Страницы: 143

Бренд: Panasonic Страницы: 73

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 90

Бренд: Panasonic Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды