JRC JLR-21 Скачать руководство пользователя страница 78

Страница: 78 / 164

5-14

5.3.1 Display Settings

Selecting

DISPLAY

from the "5.3 Main Menu" displays the Setup Menu.

From the Setup Menu you can set the contrast, brightness levels, and change buzzer settings.

1. Press the keys to move the cursor and select an item.

2. Press the key to display the menu for the selected item.

• Press to return to the Main Menu.

The following submenus are available.

• CONTRAST:

Adjusts LCD contrast. (Refer to 5.3.1.1)

• DIMMER:

Adjusts LCD brightness. (Refer to 5.3.1.2)

• CLICK SOUND:

Turns click sound on or off. (Refer to 5.3.1.3)

• REVERSING MODE:

Reverses black and white of display screen. (Refer to 5.3.1.4)

• START SCREEN

First screen after power up is selected.

The Screen allocated in the DISP key can be selected.

(Refer to 5.3.1.5)

• DECIMAL DISP SIZE:

Select the display size of decimal numbers on the screen.

(Refer

5.3.1.6)

• COMP-C/D POSITION DIGIT: Select 3 or 4 digits for displaying the current position on

the Compass screens C/D. (Refer to 5.3.1.7)

• CURRENT LAYERS:

Select the layer of current for displayed. (Refer to 5.3.1.8)

Setup Menu

Procedure

Memo

Содержание JLR-21





































































































































































Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды

JRC JLR-21, Инструкция по эксплуатации

Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды