JRC JLR-21 Скачать руководство пользователя страница 101

Страница: 101 / 164

5-37

5.4 Maintenance

Menu

Use the Main Menu to confirm or change function settings.

Press and hold both and for 3 seconds or more to display the Maintenance Main
Menu.

1. While holding down the key, press and hold the key for 3 seconds or more.

2. Use the keys to select an item, and press the key.

The Maintenance Menu disappears if one of the following is done. (be canceled)

•  The        key is pressed.

•  The power is turned off.

•  A screen other than the Settings menu is displayed for 3 min or more.

The following submenus are available.

• ANT CHECK:

(Refer to 5.4.1) Displays sensor information.

• INPUT CHECK:

(Refer to 5.4.2) Displays input information.

• DIAGNOSIS:

(Refer to 5.4.3) Performs self-diagnosis on equipment.

• DEMO:

(Refer to 5.4.4) Initiates equipment demonstration.

• PRODUCT TYPE:

(Refer to 5.4.5) Sets unit as subdisplay, confirm the equipment

number.

• RESET:

(Refer to 5.4.6) Restores all settings to their factory defaults.

• SOFT UPDATE:

(Refer to 5.4.7) Updates software.

• CCRP:

(Refer to 5.4.8) Allows CCRP settings.

Maintenance Main Menu

Procedure

Memo

Press and hold both and

In Maintenance
Mode,

Ｍ

mark is

displayed.

Содержание JLR-21





































































































































































Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды

JRC JLR-21, Инструкция по эксплуатации

Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды