JRC JLR-21 Скачать руководство пользователя страница 110

Страница: 110 / 164

5-46

5.4.7

Software Update (SOFT UPDATE)

Selecting

SOFT UPDATE

from the "5.4 Maintenance Menu" displays the software update

selection screen.

1. Press the key, use the keys to select the area to be written to, and

press the
key to confirm.

2. Select the transmission speed (bit rate). (Selection is automatic for sensor)

3. Press the keys to move the cursor to

UPDATE STANDBY

, and press the

key.

Displayed when
preparation is complete:

* Once the preparation completed message is displayed, you cannot return to the standard

screen. If you do not intend to update the software, reboot the system.

4. Connect a computer, and transfer the program.

The following submenus are available.

• UPDATE AREA:

Select the area for the update (DISPLAY/SENSOR).

• BIT RATE FROM PC:

Select the update transfer speed.

• Press to return to the Main Menu.
• Please contact JRC or an affiliate regarding software updates.

Software Update Menu

Memo

Procedure

STANDBY OK
CONTROL A PC, TRANSMIT SOFTWARE!!
CAN USE ONLY “DIM” + “PWR” KEY

Содержание JLR-21





































































































































































Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды

JRC JLR-21, Инструкция по эксплуатации

Результаты поиска

Содержание JLR-21

Отзывы:

Похожие инструкции для JLR-21

Бренды по названию

Популярные бренды