JR ProPo XG6 Скачать руководство пользователя страница 24

Страница: 24 / 84

▋

Sub▋Trim【SUB▋TRIM】

▋

Function▋Explanation

This allows fine trimming of the servos attached to each channel. This trim should be used as

a fine adjustment when the servo horn mounting angle is not 90 degrees with regard to the

linkage. Note that if large amounts of sub trim are used, it will affect the maximum deflection of

the servo. It is therefore recommended to use only small values here.

▋

Setting▋Method

Rotate the dial to move to and select the channel that you wish to set (inverse display). Then

press the dial to display the setting box, and carry out the numerical value setting.

※ The channel names on the screen will differ according to the model type.

▋

Caution▋Note

⿟ Operate the servos and carefully confirm the control surfaces move as expected before flying.

⿟ As noted above, this function is a fine tuning function to adjust the servo neutral. It is highly recommended to

adjust the neutral as much as possible using the linkages and servo horn positions.

⿟ Note that Swash type or Wing type settings may change the channel indications.

• Swash type【SWASH TYPE】・・・・・ Page 64

• Wing Type【WING TYPE】・・・・・・ Page 65

Function▋List

DANGER

CAUTION

Helicopter

Airplane

Glider

WARNING

Select Channel

Helicopter mode shown on the screen

Amount for Sub-Trim

XG6.indd 22

12/03/01 16:03

Содержание XG6





















































































Результаты поиска

Содержание XG6

Отзывы:

Похожие инструкции для XG6

Бренды по названию

Популярные бренды

JR ProPo XG6, Руководство по эксплуатации

Результаты поиска

Содержание XG6

Отзывы:

Похожие инструкции для XG6

Бренды по названию

Популярные бренды