JR ProPo XG6, Руководство по эксплуатации

Страница: 32 / 84

30
▋ Gyro▋Sensitivity【GYRO▋SENS】
▋
▋
Function▋Explanation
It is possible to adjust the Gyro sensitivity by using the gear channel (GEAR). The sensitivity can
be adjustable manually selecting for each Flight mode or Hold Switch, or can be set using the "AUTO" function.
There are two gyro sensitivity modes available - “NORMAL” and Tail Lock (T.LOCK) - choose the type depending
on your application.
▋
▋
Setting▋Method
Select the switch for changing the gyro sensitivity either manually or "AUTO" and move the cursor to each
position to input the numerical sensitivity value on the display. If “AUTO” is selected, individual sensitivity
switching for each flight mode will be applied.
⿟ Selection of Sensitivity
Select either Normal Mode or Tail Lock Mode.
⿟ Switch for Gyro Sensitivity (SW)
Under manual operation, select either Flight Mode (F.MOD SW) or Hold Switch (HOLD SW) Under auto operation,
depending on the flight mode switch, Select "AUTO".
⿟ Gyro sensitivity Switching delay (DELAY)
To avoid excessive servo hunting when switching the gyro sensitivity from a low sensitivity to higher sensitivity
setting, (when changing to a flight mode with lower rpm, but the blade rpm is not yet stable) it is possible to set a
delay on this function.
Note: During switching, the time will be delayed only when switching to a higher sensitivity.
⿟ Trim Input Function (TRIM IN)
Gyro sensitivity can be input by
the rudder trim lever. By setting
this function it is easy to adjust the
sensitivity using the rudder trim
lever during flight.
⿟ Gyro Sensitivity adjustment often
consists of two parts as shown in
the diagram. Read the instructions
with your Gyro unit and become
familiar with correct operation.
Select the Gyro Sensitivity to suit
with your application.
※感度の図を表示。
⿟ Concerning Trim Input, it is possible
to adjust the Gyro sensitivity value
using the rudder trim lever, which is
a very useful function for setting the
sensitivity during flight.
▋ ▋ Caution▋Note
⿟ Be sure to understand your Gyro manual to allow correct use of this function.
Carefully check the direction of the tail servo and be sure that everything works correctly before flight.
Function▋List
DANGER
CAUTION
Helicopter
Airplane
Glider
WARNING
Gyro gain value and actual output value
TRIM INPUT Function (TRIM IN)
GYRO SENS with delay (DELAY)
Switch for GYRO SENS (SW)
Selection of Sensitivity
2,100 [
μsec
]
900 [ μsec ]
1,100 [
μsec
] 1,500 [
μsec
] 1,900 [
μsec
]
TRAVEL ADJUST -150% -100% +100% +150%
【N】Normal mode
Usable Gain area
【N】Normal mode
Usable Gain area
【T】Tail lock mode
Usable Gain area
【T】Tail lock mode
Usable Gain area
Higher Higher Higher Higher
Higher Higher
Lower Lower Lower Lower
Lower Lower
±0%
Normal Mode
NORMAL
Tail Lock Mode
T.LOCK
Usable gain area Usable gain area
0% 50% 100% 125%
0% 0% 50% 100% 150%
100% 50% 150%
N : Normal Mode
T : Tail Lock Mode
Gyro gain value and actual output value
TRIM INPUT Function (TRIM IN)
GYRO SENS with delay (DELAY)
Switch for GYRO SENS (SW)
Selection of Sensitivity
2,100 [ μsec ]
900 [
μsec
]
1,100 [ μsec ] 1,500 [ μsec ] 1,900 [ μsec ]
TRAVEL ADJUST -150% -100% +100% +150%
【N】Normal mode
Usable Gain area
【N】Normal mode
Usable Gain area
【T】Tail lock mode
Usable Gain area
【T】Tail lock mode
Usable Gain area
Higher Higher Higher Higher
Higher Higher
Lower Lower Lower Lower
Lower Lower
±0%
Normal Mode
NORMAL
Tail Lock Mode
T.LOCK
Usable gain area Usable gain area
0% 50% 100% 125%
0% 0% 50% 100% 150%
100% 50% 150%
N : Normal Mode
T : Tail Lock Mode
ダイヤル
TIPS
調整ポイント表示
ポイント接続を曲線に変更 スティック入力位置と出力位置の数値表示
現在の
フライトモード位置
各調整ポイントの
入力位置と出力位置
ポイントの
追加と削除
注意：
グラフはホバリン
グスロットルやス
ロットルトリムで
変化する場合もあ
ります。
カーブをコピー
XG6.indd 30 12/03/01 16:03