JR ProPo XG6 Скачать руководство пользователя страница 13

Страница: 13 / 84

▋

Binding▋Procedure

In order for the transmitter and receiver to communicate, it is essential to pair or bind them together.
Please follow this procedure:

Be sure that the remote antenna unit is properly

connected to the receiver. Locate the included bind

plug, and ensure the transmitter and receiverbatteries

are fully charged.

※ Note that the Remote Antenna acts as both a receiver

and also transmits data back to the transmitter.

Carefully note the orientation of the antenna within the

remote unit. This orientation is extremely important.

On the transmitter access the “BIND & RANGE” menu

under the System List.

Refer to the Page 57 "Bind and Range Check【BIND&RANGE】
"

Inserting the bind plug into the bind terminal of the

receiver and connect the battery to a spare channel (such

as the AUX channel) - the LED’s on the receiver and the

remote antenna will begin to blink (Ready to Bind).

※ Be sure to insert the bind plug before connecting the

battery.

Refer to the “BIND & RANGE CHECK” Screen in the

transmitter System Setting mode. Press the dial to start

the binding process.

‘Binding’ will flash on the transmitter display, and

upon completion of the binding process, it will display

“SUCCESS ! PLEASE CHECK FAIL SAFE”.

Concurrently, both receiver’s LED’s will stop flashing

and be solid. signifying completion of the bind process.

If the LED’s continue to blink, repeat the procedure

from the beginning. Next, disconnect the bind plug

from receiver, disconnect the receiver battery and

switch off the transmitter.

Lastly, connect a servo, turn on the transmitter then

receiver, and confirm that communications have been

established. Range Check This checks the performance

of the transmitter by lowering the power output to

simulate a long distance range test. Under the ”Bind &

Range Check” setting screen, move the cursor to the

POWER: NORMAL column and change it to LOW. The

transmitter LED shall flash Blue to indicate it is set to

low power mode. When in this mode, walk a distance of approximately 40m from the aircraft and confirm that the

transmitter operates the aircraft normally. Continue testing as you walk around the aircraft.

Refer to the Page 57 "Bind and Range Check【BIND&RANGE】"

※

If the Radio wave reception is weak, the LED lights on receiver may flash or turn off.

(pairing the transmitter and receiver)

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

間違ったアンテナの設置方向

アンテナに対しての受信方向を表記

Receiving Sensitivity (High)

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Weak

Signal

Strong

Reception

Strong

Reception

The antenna part should be installed

in a perfectly straight condition.

RG Cable

RG631B

Remote Antenna

Strong

Reception

Strong

Reception

Weak

Signal

※The remote antenna

receives data

and also feeds back

to the transmitter

(telemetry).

▼ Front Face

▲ Rear Face

RA01T/C Side View

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitiv-

ity will be considerably degraded.

Location of LED light

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

各アンテナを互いに水平に設置すると、単一方

向の受信になるため、受信効率が低下します。

Bind plug

Binding terminal

Connecting

the battery to a

spare channel

RX battery

(sold separately)

Connection Chart

Switch harness

(sold separately)

Y-Harness

(sold separately)

RG631B Receiver

ORANGE

BROWN

RED

( )
( )

( )

ORANGE

BROWN

RED

( )

BROWN

( )

RED

( )

ORANGE

( )

Harness connection

Insert the connector,

taking adequate care

of the direction.

Sensor Installation

When connecting sensors, connect

a Y-Harness (sold separately) to the

(BIND/BATT/SENS) terminal.

Note that Sensors do not need

to be bound together with the

Transmitter and receiver.

C o a x i a l p a r t o f t h e

antenna can be bent

however, do not bend it

in a sharp angle. This

will damage the internal

antenna wires.

SENSOR

SENSOR

(sold separately)

Optional Remote Antenna RA01T/C

Preparation

XG6.indd 11

12/03/01 16:03

Содержание XG6





















































































Результаты поиска

Содержание XG6

Отзывы:

Похожие инструкции для XG6

Бренды по названию

Популярные бренды

JR ProPo XG6, Руководство по эксплуатации

Результаты поиска

Содержание XG6

Отзывы:

Похожие инструкции для XG6

Бренды по названию

Популярные бренды