JR ProPo XG11MV Скачать руководство пользователя страница 96

Страница: 96 / 136

▋

Bind▋and▋Range▋Check【BIND&RANGE】

▋

Function▋Explanation

This function allows binding (pairing) with the receiver. In addition, transmitter power output can

be reduced for carrying out a range check.

Reference page

፧

Refer to the Page 10 "Binding Procedure

(pairing the transmitter and receiver)"

፧

Refer to the Page 11 "DMSS Easy Bind system (EZ BIND SYSTEM)"

፧

Refer to the Page 15 "DSM2 Binding Method"

▋

Setting▋Method

⿟

Binding (BIND)

Set the receiver to the Bind Standby condition. Then rotate the dial to select “BIND” (inverse display) and press

the dial. If the display shows “SUCCESS”, binding has been successfully completed. If the display shows “TIMEOUT

PLEASE TRY AGAIN”, the bind process failed, and you must try again.

⿟

POWER (RF POWER) Range Check

If POWER is changed from “NORMAL” to “LOW”, the transmitter RF power is reduced and the LED will flash,

allowing a range check to be carried out. Place the Aircraft 40 meters (approx 131 feet) away from the

transmitter, and ensure all the controls function normally.

⿟

Regional Settings Mode (DMSS 2.4GHz Band width for France)

When using the transmitter in France and its overseas territories, this should be set to “FRANCE”. In all other

regions this should be set to “GENERAL”. In France mode, the 2.4GHz bandwidth that is used will be legally

restricted compared to the bandwidth in other regions. Initially it is set to “GENERAL”.

ダイヤル

TIPS

調整ポイント表示

ポイント接続を曲線に変更

スティック入力位置と出力位置の数値表示

現在の

フライトモード位置

各調整ポイントの

入力位置と出力位置

ポイントの

追加と削除

注意：

グラフはホバリン

グスロットルやス

ロットルトリムで

変化する場合もあ

ります。

カーブをコピー

⿟

If there is a difficulty in binding a receiver, please confirm the following:

፧

Are the transmitter and receiver batteries fully charged? Please fully charge the batteries.

፧

Are the transmitter and receiver too close to each other? If they are set too close each other, RF swamping

may interrupt the binding process. Please try binding again with the transmitter and receiver further

separated.

፧

If the transmitter and receiver are on a metal table or desk, binding may be difficult. Please try binding on a

different surface.

⿟

Only matching DMSS receivers may be bound to the transmitter when using the DMSS module.

▋

Caution▋Note

⿟

Be sure to set the “FAIL SAFE” (under System List) after the binding procedure is complete. It is essential to use

the Fail safe to minimize the risks of RF signal loss. Be conscious about safety all the time. Check the actual Fail

safe settings by turning off the transmitter, and monitoring the response of the servos.

⿟

When the model or type is changed in the transmitter, it will be necessary to re-bind the receiver.

⿟

NEVER fly the aircraft in Range Check mode.

DANGER

CAUTION

Helicopter

Airplane

Glider

WARNING

System▋List▋

※ For DMSS Module

Bind mode

Содержание XG11MV









































































































































Результаты поиска

Содержание XG11MV

Отзывы:

Похожие инструкции для XG11MV

Бренды по названию

Популярные бренды

JR ProPo XG11MV, Руководство по эксплуатации

Результаты поиска

Содержание XG11MV

Отзывы:

Похожие инструкции для XG11MV

Бренды по названию

Популярные бренды