JR ProPo XG11MV Скачать руководство пользователя страница 12

Страница: 12 / 136

▋

Binding▋Procedure▋

▋(pairing▋the▋transmitter▋and▋receiver)

In order for the transmitter and receiver to communicate, it is essential to pair or bind them together.

Please follow this procedure:

Be sure that remote antenna unit is properly connected to the receiver.

Locate the included bind plug, and ensure the transmitter and receiver

batteries are fully charged.

※ Note that the Remote Antenna acts as both a receiver and also transmits

data back to the transmitter.

On the transmitter access the “BIND & RANGE” menu under the System

List.

Refer to the Page 94 "Bind and Range Check【BIND&RANGE】"

Insert the bind plug into the bind terminal of the receiver

and connect the battery to a spare channel (such as the

AUX channel) - the LED’s on the receiver and the remote

antenna will begin to blink (Ready to Bind).

Note:

Be sure to insert the bind plug before connecting the

battery.

Refer to the “BIND & RANGE CHECK” Screen in the transmitter System

Setting mode. Press the dial to start the bind process.

‘Binding’ will flash on the transmitter display, and upon completion of

the binding process, it will display “SUCCESS ! PLEASE CHECK FAIL

SAFE”. Concurrently, both receiver’s LED’s will stop flashing and be

solid – signifying completion of the bind process. Disconnect the bind

plug from receiver, disconnect the receiver battery and switch off

transmitter.

Lastly, connect a servo, turn on the transmitter then receiver, and

confirm that communications have been established. If the LED’s

continue to blink, repeat the procedure from the beginning.

Range Check

This checks the performance of the transmitter by lowering the power

output to simulate a long distance range test. Under the” Bind & Range Check” setting screen, move the cursor to

the POWER: NORMAL column and change it to LOW. The transmitter LED shall flash Blue to indicate it is set to low

power mode. When in this mode, walk a distance of approximately 40m from the aircraft and confirm that the

transmitter operates the aircraft normally. Continue testing as you walk around the aircraft.

Refer to the Page 94

"Bind and Range Check【BIND&RANGE】"

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Strong

Reception

Receiving Sensitivity (High)

RG Cable 150

Remote Antenna

Built-in Antenna

▼ Front Face

▲ Rear Face

RA01T Side View

[XG7の場合]

バインド出力

画面

Location of LED light

Bind terminal

Bind plug

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters

[XG7]

ステータスLED

※ When using a gyro, carry out

the connections according to

the gyro operation manual.

RX battery

BIND PLUG

SENSOR

Insert the connectors,

taking care of the

direction.

Rudder channel

Elevator channel

Aileron channel
/ Right Aileron(Glider)

Throttle channel
/ Right Aileron(Glider)

Auxiliary channel

RG1131B Receiver

Auxiliary channel

・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)

・FLAP(Airplane/Glider)
・PIT.(Helicopter)

Bind plug

This is used during

the bind procedure.

Switch harness

Y harness

When connecting

sensors, connect a

Y-Harness (sold

separately) to the

(BIND/BATT/SENS)

terminal.

Weak

Signal

Strong

Reception

Strong

Reception

Weak

Signal

Strong

Reception

※The remote antenna receives data

　and also feeds back to the transmitter

(telemetry).

Built-in Antenna

Circuit Board Face

The built-in antenna of the remote antenna is

installed on the surface of the circuit board.

Care will be required in the situation where the

built-in antenna has been installed beside a

shielding material, since the receiving sensitivi-

ty will be considerably degraded.

Coaxial part of the antenna

can be bent however, do

not bend it in a sharp

angle. This will damage

the internal antenna wires.

The antenna part should be installed

in a perfectly straight condition.

Wrong Antenna Installation

If each antenna is installed in parallel,

the receiving eﬃciency will be reduced.

The arrows show the receiving direction with

regard to the antenna.

Receiving

Sensitivity

(Low)

Material Frame

Receiving

Sensitivity

(High)

Receiving Sensitivity (High)

※Take care not to

damage the anten-

nas projecting from

the aircraft body.

Aircraft body surface made

from shielding material.

Connect the

battery to a

spare channel

(such as AUX

channel)

Preparation

Содержание XG11MV









































































































































Результаты поиска

Содержание XG11MV

Отзывы:

Похожие инструкции для XG11MV

Бренды по названию

Популярные бренды

JR ProPo XG11MV, Руководство по эксплуатации

Результаты поиска

Содержание XG11MV

Отзывы:

Похожие инструкции для XG11MV

Бренды по названию

Популярные бренды