manualshive.com logo in svg

JPS RTU-292C, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS RTU-292C Скачать руководство пользователя страница 45

RTU-292C Operations Manual 

 

        

 

 

 

 

 

3-3 

3.2.11

 

TEL VOX 

This  button  enables  keying  of  the  radio  transmitter  by  the  RTU-292C  VOX  (Voice  Operated 
Xmit) facility.  When the VOX is selected (associated LED ON), the VOX is active, and the key 
relay is energized when the VOX circuitry detects a signal from the telephone line.  The VOX 
PTT output has a “hang” time to keep it from dropping out during short pauses in speech.  The 
hang time duration is the length of time that the PTT signal will remain active following the loss 
of  detection  of  signal.    (The  hang  time  is  internally  adjustable;  see  Section  0).    If  the  TEL 
LINE/RADIO LED continues to flash for more than ten seconds after the TEL LINE/RADIO 
pushbutton has been pressed to make a connection, the unit has not adapted properly and VOX 
operation will not be possible. 

3.2.12

 

AUTO ANS BUTTON 

This pushbutton may be used to manually enable (LED ON), or disable (LED OFF), the Auto 
Answer feature.   When enabled, the RTU-292C is in the Automated Operation Mode and the 
unit will automatically answer the phone after 2 rings.  See Section 3.7for a description of the 
Automatic Operation capabilities of the RTU-292C. 

3.2.13

 

AUDIBLE RING BUTTON 

This button determines if the ring from an incoming telephone call will be heard via the RTU-
292C’s speaker.  When the Audible Ring mode is enabled, the ring signal will be audible in the 
speaker.    The  ring  volume  is  independent  of  the  SPEAKER  VOLUME  setting,  and  is  set 
internally by adjustment R156.  Regardless of the position of the AUDIBLE RING button, the 
LED indicator associated with the TEL LINE/PHONE button flashes on an incoming ring, so 
that a visual indication of the ring signal (incoming call) is always provided. 

3.2.14

 

KEY PUSHBUTTON 

This  pushbutton  operates  the  key  function  of  the  RTU-292C,  sending  a  key  command  to  the 
associated transmitter.  This button is functional at all times.  The red KEYED LED next to the 
KEY pushbutton is lit whenever a key command is sent to the transmitter from any source within 
the  RTU-292C  (handset  keyswitch,  or  TEL  VOX,  for  example),  not  just  from  the  KEY 
pushbutton. 

3.2.15

 

PEAK LED 

This red LED flashes on audio peaks that are detected in the audio incoming from the receiver to 
indicate  the  proper  adjustment  of  the  internal  RX  LEVEL  control  (R116).    The  input  level  is 
correct  when the PEAK  LED flashes occasionally  on incoming receiver  speech peaks.    If the 
LED flashes continuously, the input level is too high and should be reduced (see Section 2.10).  
Note that this LED does not respond to telephone audio. 

3.3

 

REAR PANEL CONNECTORS 

Accessible at the RTU-292C rear panel are the radio connector, telephone line, the DC power 
terminal block, an RS-232 connector, and the DIN plug for connecting the external AC power 
supply.  See Section 2.9 for full pin-out information. 

3.3.1

 

P1 RADIO CONNECTOR 

This male DB9 connector is the interface between a radio system and the RTU-292C.  It contains 
transmit audio, receive audio, and keylines.  

Содержание RTU-292C





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды