manualshive.com logo in svg

JPS RTU-292C, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS RTU-292C Скачать руководство пользователя страница 93

RTU-292C Operations Manual 

 

        

 

 

 

 

 

6-5 

6.4

 

SQUELCH BREAK ACCESS OPTION 

This option allows a radio user who does not have DTMF capability to quickly place a telephone 
call via the RTU-292C.  The radio user simply transmits a series of squelch breaks and is then 
automatically connected to the telephone at the RTU-292C speed dial location #01.  To use the 
squelch  break  feature,  the  local  radio’s  squelch  output  must  be  connected  to  the  RTU-292C 
/External Signal Input, and the RTU-292C continuously monitors this line for the correct squelch 
break timing.  The RTU-292C will respond to either a positive going or negative-going squelch 
signal.  

 

NOTE 

It is possible to enable this option remotely.  If you have purchased an RTU-292C 
without this option and want to add it, contact us. 

 

6.4.1

 

Initiate Call Via Attention Signal 

The radio user sends the “Attention” signal to the RTU-292C.  This is a series of 3 squelch breaks 
that occur within 4 seconds window. 

6.4.2

 

RTU-292C Response to Attention Signal 

The RTU-292C will respond with the voice prompt “

RTU-292C automatic phone patch”.

  The 

Acknowledge (ACK) Tone prompt is also given. 

6.4.3

 

RTU-292C Prompts for Confirmation 

The RTU-292C then requests confirmation with the prompt "

Please confirm with a single squelch 

break

”.  The caller confirms his desire to call by giving 1 additional short squelch break within 

5  seconds.    If  the  RTU-292C  does  not  receive  confirmation  within  that  time,  it  will  give  a 
"Timeout" tone prompt, terminate the attempt to call, and go back to its waiting state. 

6.4.4

 

RTU-292C Places the Call 

The  RTU-292C  then  informs  the  radio  user  that  the  call  is  being  placed.    The  ringback 
information that is provided when placing a call via the RTU-292C front panel keypad is not sent 
over the air due to FCC regulations.  The RTU-292C adapts to the phone line while placing the 
call. 

If the number is busy, the busy tones will be broadcast for approximately 5 seconds before the 
RTU-292C terminates the call attempt. 

Once the RTU-292C detects ringback, the RTU-292C begins a 30 second timer and waits for the 
call  to  be  answered.    If  this  does  not  happen  before  the  timer  expires,  the  call  attempt  is 
terminated. 

6.4.5

 

After the Call Begins 

The call can now proceed, and the Inactivity Timer will now begin to run.  If this time expires 
(because no speech or other activity is heard), the RTU-292C will give a series of 3 short beeps 
as a warning.  The radio caller or the phone user may initiate activity within 5 seconds of the 
warning beeps to reset the timer.  If neither user does so, the unit will then terminate the call. 

Содержание RTU-292C





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды