manualshive.com logo in svg

JPS RTU-292C, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS RTU-292C Скачать руководство пользователя страница 78

 

             

RTU-292C Operations Manual

 

 

 

 

 

 

4-18 

4.5

 

CALL PROGRESS RESPONSES FROM THE RTU-292C 

The following section describes the responses the user may expect from the RTU-292C when 
Call Progress is active.  Call progress is active whenever the PSTN is “off-hook”. 

 

Table 4-3 

Call Progress Responses 

%CP_RING Exx <CR>  

Call Progress detects Ringback.

 

%CP_BUSY Exx <CR> 

   

Call Progress detects a Busy signal.

 

%CP_NO_ANS Exx <CR> 

   

No answer after the DIAL command originated a call.

 

%CP_NO_DIALTONE Exx <CR> 

   

No dial tone when the DIAL command originated a call.

 

%CP_AUTO_ANSWERED Exx <CR>

.

 

The RTU-292C has answered an incoming PSTN call

 

 

4.6

 

RESPONSE ERROR CODES 

All responses from the RTU-292C include an error code.  This error code allows the user to see 
if there were any problems with a given command.  

Unless otherwise noted the user may assume 

that a non-zero error code indicates that the command was not acted upon

. 

 

Table 4-4 

Response Error Codes

 

E0 

No error. 

E1

 

The previous command is unknown. 

E2

 

The previous command was missing required parameter(s). 

E3

 

The previous command had a parameter that was out of the allowed range for this command. 

E4

 

The previous command requested a resource that is not available.  An example of this would be 
a DIAL command sent to the Local Phone option, when the Local Phone option is not installed. 

E5

 

The previous command requested a resource that is currently busy.  An example of this would 
be a DIAL command received when the RTU-292C is already off hook. 

E6

 

The previous command may not be used at this time.  An example of this would be a DTMF 
command received when the RTU-292C is still on-hook. 

E7

 

A hardware related fault was detected.  

 

 

 

 

 

End of Section 4 

Содержание RTU-292C





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды