manualshive.com logo in svg

JPS RTU-292C, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS RTU-292C Скачать руководство пользователя страница 92

 

             

RTU-292C Operations Manual

 

 

 

 

 

 

6-4 

6.3.1

 

Initiate Call Via Attention Signal 

The radio user sends the “Attention” signal to the RTU-292C.  The attention signal consists of 
the DTMF characters “

* * *

” (three stars). 

6.3.2

 

RTU-292C Response to Attention Signal 

The RTU-292C will respond with the voice prompt “

RTU-292C automatic phone patch.  Enter 

phone number followed by the “pound” sign or stand by for auto-call

”.  The RTU-292C will 

also give the Acknowledge (ACK) tones.  If Password Protection is enabled, the RTU-292C will 
request the correct password prior to asking for the telephone number. 

6.3.3

 

Radio Caller Provides Calling Directions 

The radio user can then enter a phone number (terminated by the # sign), or “* n n #” for speed 
dial location “nn”.  If the caller forgets to enter “#” the RTU-292C will simply wait 4 seconds to 
ensure that data entry is complete and then begin to place the call.  If no DTMF is detected at the 
RTU-292C, the unit will place a call to the telephone at the speed dial location #01.  This is an 
“auto-call”. 

6.3.4

 

RTU-292C Plays Back Phone Number & Prompts for Confirmation 

The RTU-292C will play back the number it intends to dial.  In the case of speed dial numbers, 
it only plays back the speed dial location and not the number stored at that location.  The RTU-
292C then prompts the caller for confirmation with  the prompt “

Please confirm by entering a 

single  “Star”  digit

”,  along  with  the  Query  tone  prompt.    If  the  RTU-292C  does  not  receive 

confirmation within five seconds, it will give a Timeout prompt and go back to its waiting state.  

6.3.5

 

RTU-292C Places the Call 

The  RTU-292C  then  informs  the  radio  user  that  the  call  is  being  placed.    The  ringback 
information that is provided when placing a call via the RTU-292C front panel keypad is not sent 
over the air due to FCC regulations.  The RTU-292C adapts to the phone line while placing the 
call. 

If the number is busy, the busy tones will be broadcast for approximately 5 seconds before the 
RTU-292C terminates the call attempt. 

Once the RTU-292C detects ringback, the RTU-292C begins a 30 second timer and waits for the 
call  to  be  answered.    If  this  does  not  happen  before  the  timer  expires,  the  call  attempt  is 
terminated. 

6.3.6

 

After the Call Begins 

The RTU-292C now enters its "Command Mode", meaning that the phone user may enter any of 
the available DTMF commands from Table 3-1. The Inactivity Timer will now begin to run.  If 
this time expires (due to a lack of speech or other audio activity), the RTU-292C will give a series 
of 3 short beeps as a warning.  The radio caller or the phone user may initiate activity within 5 
seconds  of  the  warning  beeps  to  reset  the  timer.    If  neither  user  does  so,  the  unit  will  then 
terminate the call. 

To terminate the call at any time, the radio user may enter 

* #

 at any time.  The phone user may 

also enter 

* #

 to hang up. 

Содержание RTU-292C





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды