Jøtul GF 370 DV MV Скачать руководство пользователя страница 18

18

130102- 1   GF 370 DV MV   2/22

6.  High Altitude Adjustment

The decreased atmospheric pressure of higher altitudes af-

fects heat value of gaseous fuels.  Most gas suppliers derate 

the gas intended for use at elevations above 2000 feet. 

Check with your gas supplier before performing derate 

adjustment to the burner.
This appliance may be adjusted for altitude over 2000 ft. 

(610 - 1371 m) for natural gas.  

If the gas supplier does not derate fuels, install High Alti-

tude Adjustment Kit 156822 for Natural gas.  

 

DO NOT DERATE FOR PROPANE.
U.S & Canada per 

ANSI Z21.88-2019•CSA 2.33-2019, CAN/CGA 2.17

For natural gas installations from 610-1370 meters 

(2000-4500 ft.) the orifice size (DMS) is #39.  See 

data plate for additional information. For high altitude 

installations consult the local gas distributor or the 

authority having jurisdiction for proper rating methods. 

If the installer must convert the unit to adjust for varying 

altitudes, the information sticker must be filled out and 

applied to the appliance at the time of the conversion. 

INSTALLER: Fill out the appropriate information and 

apply the high altitude conversion label provided to the 

rating plate on the appliance. See fig. 7.8.

Derating Procedure

•  Follow Steps 1-16 of the Fuel Conversion procedure on 

pages 16 to change the burner injector. Use the injec-

tor supplied with the kit.  Detailed instructions are also 

included in the kit.     

•  Conduct gas leak and gas pressure tests as detailed on 

page 15 of this manual.

•  Conduct system check and flame picture adjustments as 

specified on pages 21-22. 

Figure 7.8. High Altitude Conversion Label.

This appliance has been converted for use at an altitude 

of___________ .

Orifice Size: __________ Manifold Press. _______

Input Btu/Hr. _________  Fuel Type  ___________

Date: ___/___/___   Converted by:_____________

Cet appreeil a été converti au _____  Injecteur_____   

Pression à la tubulure d’alimentation ___________Déoit 

calorifique ___________

7.  Firebox Panel Installation

Skamol Panels and optional 

Reflective Glass Kit 156817

Skamol Panels

These insulating panels are installed at the factory. 

If 

desired, the panels may be painted black using any high-

temperature paint. 

THE SKAMOL PANELS MUST BE LEFT IN PLACE.  

DO NOT OPERATE THE STOVE WITHOUT THE SKA-

MOL PANELS INSTALLED.

Reflective Glass Panels

    

Tools:  1/4” socket driver

     Optional: High-temp Black Paint may be applied to the 

exposed edges of the side Skamol panels to match the black 

glass. 

Cotton gloves are provided with the glass panels. Use them 

to handle the panels to prevent fingerprints on the surfaces. 

Fingerprints are difficult to remove. Use a clean cloth to remove 

any dust from the glass panels.

1.  Remove the Upper Retainer Bracket from the firebox 

with removal of three #8 x 12 sheet metal screws.  See 

fig. 7.9. 

2.  Remove the Lower Panel Retainer from the back of the 

burner skirt with removal of three #8 x 12 sheet metal 

screws. 

3. 

Orient the rear panel, 

smooth side out, textured side 

in. 

Rest the bottom of the panel on the burner skirt, 

centered against the back wall. See fig. 7.10.  

4.  Orient the side panels, smooth side out, and sliding each 

behind the retainer wings.  See Fig. 7.11.

5.  Push the Upper Retainer back against the glass panels 

and tighten the three sheet metal screws.

6.  Replace the Lower Panel Retainer.

Содержание GF 370 DV MV





































Отзывы: