EN
FR ES
6 Front Wheel Locks
• The front wheels can be either in swivel mode or locked mode.
• To put each front wheel set into its locked mode, push down on the locking tab located at the top of the wheel housing and between the
wheels. Be sure to push the locking tab all the way down until an audible click is heard.
See Figure 6.1.
NOTE:
You may need to rotate the front wheel so the swivel lock tab is facing the rear of the stroller.
• To unlock each wheel and put it into swivel mode, pull up on the locking tab to disengage the lock.
7 Seatback Positioning
Each seatback can be adjusted to any position from fully upright to reclining. These seats should only be used for children who are at least
3 months old. For children between 3 and 6 months, use the most reclined position. For children 6 months and older, use the more upright
positions.
• Engage the rear wheel brakes.
• Locate the recline mechanism on the backside of the seat.
• To recline a seat, grasp the buttons on the top and bottom of the recline mechanism and gently pull towards the rear of the stroller until the
seat is in the desired position.
See Figure 7.1.
• To adjust a seatback to a more upright position, pull the straps at the end of the recline mechanism rearward while pushing the
mechanism forward until the seatback is in the desired position.
See Figure 7.2.
NOTE:
To get a seatback into its most upright position you may need to push the seatback toward the front of the stroller before
pulling the straps.
!
WARNING
ALWAYS ensure that the seat back is secured into position before placing a child in the seat.
Push down on the seatback to be sure it is secure.
NEVER adjust the seatback when the child is in the seat.
Use the more upright seatback positions ONLY for children who are at least 6 months old.
8 Adjusting the Leg Supports
The leg support can be adjusted to two positions horizontal or all the way down.
• To place the leg support into the down position, locate the trigger mechanism underneath BOTH sides of the leg support on the bottom.
Squeeze BOTH triggers and rotate the leg support down.
See Figure 8.1.
NOTE:
The leg support does not “lock” into the down position, but will remain there by gravity only.
• There are fabric flaps that cover the triggers. If necessary, pull each flap over the trigger and attach the Velcro® to secure it.
• To place the leg support into the horizontal position, pull up on both sides of the leg support until it is locked into position.
See Figure 8.2.
• Push down on both sides of the leg support to ensure it is secure.
!
WARNING
NEVER allow a child to step onto or sit on the leg support. This may cause the stroller to tip over and injure the child.
9 Installing/Removing the Bumper Bar
• Remove the two safety caps from the frame mount points by pressing the release button and pulling each cap off.
See Figure 9.1.
• Locate the bumper bar and orient it with the male fitting pointed towards the seat unit and the shiny round rivet head facing upward. While
holding the male fittings straight, insert the male fittings on the bumper bar into the female fittings located on both sides of the seat. You
will hear both sides of the bumper bar “click” in.
See Figure 9.2.
• Pull outward on the bumper bar to ensure it is installed properly and securely.
• To remove the bumper bar, press the buttons located on the underside of both male fittings inward and pull the bumper bar away from the
seat.
See Figure 9.3.
• The bumper bar fabric cover can be removed for cleaning. To remove the fabric cover, simply open the zipper on the inside of the fabric
cover and pull the cover off of the bumper bar.
• To replace the cover, remove the bumper bar from the stroller, fit the cover over the bumper bar with the zipper facing inward and close
the zipper completely.
• When using the stroller without the bumper bar always replace the safety caps.
!
WARNING
The bumper bar is not a restraint device. ALWAYS secure your child with the restraint system. NEVER lift the stroller
by the bumper bar. Use caution when attaching the bumper bar when there is a child seated in the stroller.
10 Installing, Operating and Removing the Canopy
• Stand behind the stroller with the stroller in the unfolded position.
• Orient the canopy in front of the handlebar with the visor towards the front of the stroller.
• Locate the plastic slide locks on the bottom of each side of the canopy and slide them onto the plastic fitting on each side of the stroller
just above the rear leg.
See Figure 10.1.
