Jolly Mec TERMOJOLLY 80 EVO Скачать руководство пользователя страница 38

Страница: 38 / 44

08.3

ROUTINE MAINTENANCE

Opening the combustion chamber door

a) Opening the “vertical sliding” combustion chamber door with standard handle

To open the combustion chamber door (in “vertical sliding” mode), grasp the handle (1) (

1) and fully lift it (

. 2). To close it again, lift it

completely. In case of hot fireplace, use the anti-heat glove.

b) Opening the “vertical sliding” combustion chamber door with removable handle

To open the combustion chamber door (in “vertical sliding” mode), grasp the removable handle (3) (

3), insert it into the specific split (4)

and lift it completely (

. 4). To close it again, lift it completely.

c) Opening the “hinged” combustion chamber door (with vertical sliding)

To open the combustion chamber door (in “hinged” mode, for glass cleaning only) hold the lever (5) and turn it (

. 5). Open the door

completely (

. 6). This operation must be performed with cold fireplace.

d) Opening the “hinged” combustion chamber door

To open the combustion chamber door (in “hinged” mode), grasp the handle (6) and rotate it (

. 7

). Open the door completely (

. 8

). In

case of hot fireplace, use the anti-heat glove.

. 1

. 2

. 3

. 4

. 5

. 6

. 7

. 8

Содержание TERMOJOLLY 80 EVO













































Результаты поиска

Содержание TERMOJOLLY 80 EVO

Отзывы:

Похожие инструкции для TERMOJOLLY 80 EVO

Бренды по названию

Популярные бренды

Jolly Mec TERMOJOLLY 80 EVO, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание TERMOJOLLY 80 EVO

Отзывы:

Похожие инструкции для TERMOJOLLY 80 EVO

Бренды по названию

Популярные бренды