manualshive.com logo in svg

Johnson Controls TEC3010, Руководство по установке, Страница: 46 / 48

Поделиться
Скачать
Johnson Controls TEC3010 Скачать руководство пользователя страница 46

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification 

Capability Installation Instructions

46

Repair Information

If the TEC3000 Series Thermostat Controller fails to operate within its specifications, replace the unit. For a 
replacement thermostat controller, contact the nearest Johnson Controls representative.

The controller is unable to access a 
USB drive.

The drive is formatted as NTFS or 
another unsupported format. The TEC 
supports FAT16 and FAT32 formats 
only.

Reformat the USB drive, or try a 
different USB drive with a supported 
format.

The USB drive is defective.

Try a different USB drive.

The controller displays 

Board 

Mismatch

.

The I/O board that the display board is 
currently attached to does not match 
the one that initially shipped with the 
display board.

Attach the display board to the correct 
I/O board.

A hardware failure is causing the two 
boards to incorrectly identify 
themselves.

Order replacement units and return the 
affected devices to Johnson Controls 
under the RMA program.

The controller displays 

Controller 

Fault

. 

An internal fault was detected and the 
controller was unable to recover.

Order replacement units and return the 
affected devices to Johnson Controls 
under the RMA program.

The Bell icon is displayed on the TEC 
home page. 

The fault has been detected on the 
TEC.

See Table 12 for TEC fault causes and 
resolution.

Partial Restore Complete

 is displayed 

when trying to restore settings from a 
backup file. 

Not all of the items in the backup file 
have been restored. This error can be 
caused by a value being out of the 
minimum or maximum range in the 
backup file. It may also occur if there 
are inconsistencies in the reliability of a 
setting in the backup file and on the 
TEC device.

1. Create a Backup file on a USB 

drive for the TEC that is showing 
the issue.

2. Edit the backup file created in the 

previous step on a computer to 
reflect the preferred settings.

3. Verify that the modified values are 

within minimum and maximum 
range in the backup file.

4. Restore the settings from the newly 

edited backup file on the TEC. 

The temperature displayed is lower 
than the actual room temperature.

Cold air drafts are entering the back of 
the TEC.

Seal any holes behind the TEC to 
reduce drafts.

Air is being forced through the TEC 
from a nearby vent.

Move the location of the TEC or 
change the venting to prevent air from 
being forced through the TEC.

Supervisory Status = Offline

The supervisory controller is not 
communicating with the TEC. The TEC 
is not mapped to a JCI Supervisory 
System. The WNC Gateway is not 
communicating with the TEC.

1. Map the TEC into a JCI 

Supervisory system.

2. Verify that the PAN’s WNC 

Gateway is online.

3. Add ZFR Pro Routers/Repeaters 

into the wireless system.

Some icons are hidden.

Lockout levels are used or the icons 
are hidden due to the display settings.

See Table 5 for lockout levels and 
access details.

1.

For ZFR Pro Wireless information, refer to the 

WNC1800/ZFR182x Pro Series Wireless Field Bus System Technical 

Bulletin (LIT-12012356).

Table 13:  Troubleshooting Details

1

 (Part 2 of 2)

Symptom

Probable Causes

Solutions

Содержание TEC3010

















































Отзывы:

Нет отзывов