Johnson Controls TEC3010 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 48

Johnson Controls TEC3010 Скачать руководство пользователя страница 16

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

16

User Lockout

You can select from three different levels of access at the local display to manage functionality through the
supervisory controller. This lockout is independent of any display or passcode settings. The existing temporary
occupancy capability is unaffected by this feature. User lockout hides the icons that are not operable. The lockout
levels are described in Table 5.

Using the USB Port

The USB port allows you to quickly and easily load firmware upgrades, backup settings, and restore settings to the
TEC3000 by using a USB drive. The TEC3000 can recognize eight configuration files or firmware package files.
The USB drive format must be FAT or FAT32. The drive cannot be NTFS or USB 3.0. If you are upgrading firmware
or copying configuration files, you need the TEC3000 passcode, if it has been set up. Do not remove the USB drive
until the firmware upgrade is complete. The TEC3000 may restart and go offline to the NAE after a firmware
upgrade.

Loading the Firmware

1.

Ensure that the TEC screen is on.

2.

Insert the USB drive into the right side of the TEC.

See Figure 1 for the USB port location.

3.

Press the

Menu

icon.

4.

Scroll down the menu and press

Update

.

5.

Press

Load Firmware

.

6.

Select the correct firmware version. The correct file name has the .pkg extension.

7.

Press

Confirm

if you have the correct firmware version.

The firmware is loaded from the USB drive. See

Troubleshooting

if the firmware is not loaded correctly.

8.

Remove the USB drive from the TEC3000.

Backing Up the Settings

Note:

When you back up the settings, the network settings are not backed up or restored.

1.

Ensure that the TEC screen is on.

2.

Insert the USB drive into the right side of the TEC.

See Figure 1 for the USB port location.

3.

Press the

Menu

icon.

Checkmark

Indicates that an event or schedule is programmed for a specific day of the week.

Exclamation
Point

Indicates that an error has occurred.

Table 5: User Lockout Levels

Lockout Level

Capability

State 0

Allows full access to Home Screen Display Adjustments and icons (default).

State 1

Hides the

Menu

icon.

State 2

Only allows the screen to trigger temporary occupancy. Menu, Unit Power, the Up
and Down arrows, and Run/Hold are hidden.

Table 4: Touchscreen Icons (Part 4 of 4)

Icon

Icon Name

Description

«
...
14
15
16
17
18
...
»

Содержание TEC3010

















































Отзывы:

Нет отзывов