manualshive.com logo in svg

Johnson Controls TEC3010, Руководство по установке, Страница: 22 / 48

Поделиться
Скачать
Johnson Controls TEC3010 Скачать руководство пользователя страница 22

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification 

Capability Installation Instructions

22

7.

Press

to save and 

 

to return to the previous screen.

Additionally, the thermostat controller supports manual changeover. To configure manual changeover:

1.

Press the 

Menu

 icon.

2.

Press 

Equipment Setup

.

3.

Press 

Changeover

.

4.

Press 

Changeover Mode

 and select 

Heating

 or 

Cooling

.

5.

Press

to save and 

 

to return to the previous screen.

Ensure that the Supply Temp type is set to Analog Sensor. The Changeover Mode is also exposed to the BAS 
through the CGOVR-MODE and can be commanded from the BAS.

On 2-pipe or VAV systems without an automatic changeover, or on 4-pipe systems, you can use COS as a 
monitor-only point for reading an analog sensor. By setting the controller in 4-pipe mode, or selecting Heating or 
Cooling for Changeover Mode, the controller defaults to monitor-only mode for the COS and exposes the value to 
the network as the supply temperature.

Dehumidification Control - Fan Coil Only

The TEC3000 controller supports dehumidification control on fan coil devices under three configurations:

•

4-pipe fan coil

•

4-pipe fan coil with reheat

•

2-pipe fan coil (with changeover in cooling mode) with reheat

For optimal dehumidification performance, a 4-pipe unit with floating/incremental or 0 to 10 V control and a 
multi-speed or variable-speed fan is recommended.

Dehumidification operates when the zone humidity increases above the zone humidity setpoint and the controller is 
in the Idle or Cooling state. Dehumidification does not operate during heating and stops if the zone temperature 
drops below the heating setpoint. When dehumidification is active, the cooling device controls to the humidity 
setpoint, and the heating device reheats the zone in order to keep the temperature at the cooling setpoint. While in 
the dehumidification mode, a multi-speed or variable-speed fan runs at the lowest possible speed to maximize 
condensation and moisture removal across the cooling coil.

To enable dehumidification control:

1.

Press the 

Menu

 icon.

2.

Press 

Control Setup

.

3.

Press 

General

.

4.

Press 

Dehum Enable

 and select 

Yes

.

5.

Press

to save and 

 

to return to the previous screen.

This point is also exposed to the BAS through the point DEHUM-EN.

To adjust the dehumidification setpoint:

1.

Press the 

Menu

 icon.

2.

Press 

Setpoints

.

3.

Press 

Dehumidification

 and adjust accordingly.

Содержание TEC3010

















































Отзывы:

Нет отзывов