JNE TECH-D Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 25

background image

___________________________________________________________________________

______________________________________________________________________________

7

TECH-D manual EN 2010-05-18.doc

2.2 Display function

START UP TECH-D

NOTE! When you start make sure the
telescoping measuring arm is completely
collapsed.

Start the digital by pressing the button
briefly. A digital number 900 (900mm) will
appear in the display window representing the
minimum collapsed length between the height
calibration rod and datum height rod centres.

Note: If display does not read 900 - switch
off by holding down the On/0 button for a
few seconds and restart following the above
procedure.

NORMAL MEASURING

This is the automatic setting after start.
The measuring tool work in the area of

900-2650 mm

.

SHORT

MEASURES

To measure short measures, 400-2150 mm,
press for 2 seconds.
Use the tip holder that is attached underneath
the measuring arm. Use this measuring area
preferably under hood.

COMPARATIVE MEASURING

The digital reading can be reset for quick
comparative checks during normal length
measuring operations by briefly pushing the
button to select 0 mm. From this point any
change in length will register plus or minus in 1
mm gradients. Additional comparative checking
is possible by repeating the above procedure at
any time during comparative checking.

«
...
5
6
7
8
9
...
»

Содержание TECH-D


























Отзывы:

Нет отзывов

Похожие инструкции для TECH-D

Бренд: Xylem Страницы: 24

Бренд: Kane Страницы: 16

Бренд: Kane Страницы: 60

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: Kamstrup Страницы: 100

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 12

Бренд: Kamstrup Страницы: 60

Бренд: Kamstrup Страницы: 136

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 155

Бренд: Magnescale Страницы: 2

Бренд: Datakom Страницы: 27

Бренд: Kirby Morgan Страницы: 101

Бренд: BASI Страницы: 69

Бренд: Omega Страницы: 15

Бренд: TASKING Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды