background image

7. Damage to the engine where blockages in the fuel system have occurred by
unfiltered or contaminated fuel.

Jets-Munt Representatives:

Check the current dealer list on our web page,

www.jets-munt.com

Safety Notes

Please remember the engine is not a toy and has the potential to cause bodily harm to you and
others if misused. The MERLIN engine is a sophisticated piece of machinery and should be
treated with a high level of safety when it is in operation. It is your responsibility as owner, to
ensure safe, careful and considerate operation of your engine at all times, and in accordance
with the manufacturer's instructions. If you sell or give away this engine, please pass these
instructions to the new owner.

The following guidelines should be read carefully and adhered to.

1. Always keep a CO2 or similar fire extinguisher of at least 2Kg of CO2 contents close
when starting and operating the engine. Don’t use a powder extinguisher.

2. Always protect eyes and ears during the starting procedure.

3. Be aware of the extreme intake suction hazard, we advise the use of a suitable
commercial wire mesh Foreign Object Damage guard to protect the engine intake.
Ensure you have no loose items of clothing (ties, etc.) or equipment which can readily
be sucked into the engine intake, even from adjacent to the engine.

4. Always operate your engine in open air away from confined spaces as the engine
exhaust contains gases which can cause asphyxiation and nuisance smells.

5. Do not touch the engine whilst it is running. Turbines rotate at a very high rpm and
the engine casing and exhaust can reach very high temperatures. Ensure anything
affected by heat is kept well clear of the engine and exhaust during operation.

6. Never use the engine near to sources of flammable gases, liquids or materials.

7. Keep unauthorized persons, spectators, children and animals well away from the
starting area (at least 30ft or 10 meters away).

8. Always handle turbine fuel and oil with care as they are highly flammable. Store
them in appropriate labeled containers. Never dispose inappropriately. We recommend
the use of suitable disposable protective gloves for the mixing of turbine oil/fuel.
Turbine oil can be are hazardous to health and must not be allowed to come into
contact with skin, mouth, eyes or through ingestion, accidental or otherwise. Take care
when decanting and ensure any spillage is wiped away immediately and clean any
affected area with warm soapy water. Wash hands and any affected part immediately
after any contact.

4

Содержание Merlin M122NG

























Отзывы: