background image

 

 

20 

SECTION 5 

– CONCENTRATION MEASUREMENTS 

The  concentration  measurement  mode  enables  simple  measurements  of  concentration  to  be 

performed.  In  this  measurement  mode  it  is  possible  to  calibrate  against  a  standard  of  a  known 

concentration or use a known factor. The sample is measured at one wavelength at one point in time.  

To select concentration use the LEFT or RIGHT arrow keys to move the cursor to the CONC indicator 

on  the  menu  bar  (refer  to  figure  2.3.1).  The  primary  display  will  show  the  concentration  with  the 

selected units. To adjust the wavelength use the UP and DOWN arrow keys. 

To select the units use the LEFT or RIGHT arrow keys to move the cursor to the  UNITS indicator on 

the menu bar (refer to figure 2.3.1). Use the UP and DOWN arrow keys to select ppm, mg/l, g/l, M, % 

or blank units. Once the required units have been selected  press the RETURN  or CAL key to store 

the units and return to the concentration measurement mode.  

5.1 

USING A KNOWN STANDARD 

The  calibration  must  be  performed  at  the  same  wavelength  at  which  the  sample  will  be  measured. 

Insert a cuvette containing the known concentration standard into the sample chamber and close the 

instrument lid. Press the CAL key; the CAL annunciator will flash continuously. Use the arrow keys to 

change  the  concentration  to  the  required  value  for  the  standard.  Press  the  CAL  or  RETURN  key  to 

calibrate  the  instrument  to  the  standard  concentration.  The  instrument  will  calculate  the  factor  for 

subsequent measurements. If the factor calculated is out of range, then the instrument will display Err 

3 for 2 seconds after the calibration.  To view the factor use the LEFT or RIGHT arrow keys to move 

the cursor to the xF indicator on the menu bar (refer to figure 2.3.1). 

Once  the  calibration  has  been  performed  a  sample  of  unknown  concentration  can  be  measured. 

Remove the cuvette containing the standard solution and place a cuvette containing the sample to be 

measured in the sample holder. Close the instrument lid and the concentration result will be shown on 

the screen.  

Subsequent  samples  can  be  measured  in  the  same  way.  If  the  wavelength  is  adjusted  between 

sample  measurements  then  the  instrument  must  be  calibrated  again  before  more  samples  can  be 

measured. 

5.2 

USING A KNOWN FACTOR   

If the factor is known there is no need to calibrate against a known standard. To enter the factor use 

the LEFT or RIGHT arrow keys to move the cursor to the xF indicator on the menu bar (refer to figure 

2.3.1). Use the UP and DOWN arrow keys to enter the required factor. Once the required factor has 

been  entered  press  the  RETURN  or  CAL  key  to  store  the  factor  and  return  to  the  concentration 

measurement mode.  

Содержание 6305































Отзывы: