JEM Glaciator Dynamic Скачать руководство пользователя

Страница: 26 / 32

Troubleshooting

Problem

Probable cause(s)

Suggested remedy

Machine will not produce
low-fog when control panel
set to CONTINUOUS or fog
button pressed



Machine not at operating
temperature

Wait until HEAT message no
longer shown



FOG option set to 0



Increase setting



Machine in timer mode and
TIMER ON set to 0

Increase setting

DMX signal present

Disconnect or turn off DMX
controller

Machine can be fired from
control panel, but not by
DMX controller

DMX address setting
incorrect

Change DMX address (page
14)

Poor connection in DMX line

Check DMX cables and
connections

LINK menu is set to SEND

Set LINK menu to RECEIVE

Low-fog output is weak

Machine requires priming

Use PRIME option to prime
the machine (page 15)

Wet, greasy, non-uniform

low-fog output, or very loud
noise when firing machine

Incompatible low-fog fluid

Use approved fluid!

Machine appears dead

Main MCB tripped

Reset MCB on rear panel

No power at AC cable inlet

Check power cable and
supply system circuit
breakers

Machine causes DMX errors
to occur on other units when
connected to a DMX system

LINK menu is set to SEND

Set LINK menu to RECEIVE

Loss of control from remote

Communication issue
between remote and
machine

Check cable connection

between remote and
machine.
Ensure cable is no longer
than 25 m (82 ft.)

Содержание Glaciator Dynamic

































Результаты поиска

Содержание Glaciator Dynamic

Отзывы:

Похожие инструкции для Glaciator Dynamic

Бренды по названию

Популярные бренды

JEM Glaciator Dynamic, Руководство пользователя

Результаты поиска

Содержание Glaciator Dynamic

Отзывы:

Похожие инструкции для Glaciator Dynamic

Бренды по названию

Популярные бренды