Jefftron Leviathan V3 Скачать руководство пользователя

Страница: 4 / 24

External ports

Input terminal

- Leviathan has 3 pads for connecting exter-

nal button, virtual reload or sensor.

3,1V

is in the

red area

(for sensor only), it s

covered by foil - partly remove it from right

side and put it back after wire solder.

Signal

is in the

yellow area

Negative

pole is in the

green area

- External button connects on SIG and GND

pad (doesn‘t matter on polarity).

- In the app use interface „External input“ to

activate desired function.

Output pads

- Leviathan has 2 pads on the board for

powering hop-up LED illumination, flashli-

ght, laser, magazine motor etc.

Positive

pad is battery voltage (

red area

Negative

motor pad is in the

green area

- These pads cannot be controlled from the

smartphone app. The power supply will

work only when the motor is running.

WARNING

: Installation requires advanced soldering skills! Wires can‘t touch other pads

and components on the board. Damage to the Leviathan will void the warranty!

For

AUG weapon

connect external AUTO

trigger contact to

SIG

and

GND

pad.

Содержание Leviathan V3

























Результаты поиска

Содержание Leviathan V3

Отзывы:

Похожие инструкции для Leviathan V3

Бренды по названию

Популярные бренды

Jefftron Leviathan V3, Руководство по установке

Результаты поиска

Содержание Leviathan V3

Отзывы:

Похожие инструкции для Leviathan V3

Бренды по названию

Популярные бренды