Jeep 2008 Cherokee Скачать руководство пользователя страница 447

Страница: 447 / 490

Perform Maintenance Every

(Where time and mile-

age are listed, follow the interval that occurs first.)

Maintenance Items

Miles

Kilometers

or Months

Change the engine oil and engine oil filter.

6,000

10 000

Rotate tires.

6,000

10 000

If using your vehicle for any of the following: Dusty or off-road
conditions. Inspect the engine air cleaner filter, replace if neces-
sary.

12,000

20 000

Inspect the brake linings, replace if necessary.

12,000

20 000

Inspect the front & rear axle fluid, change if using your vehicle for
police, taxi, fleet, off-road or frequent trailer towing.

18,000

30 000

Inspect the CV joints. Perform the first inspection at 12,000 miles (20
000 km) or 12 months.

24,000

40 000

Inspect exhaust system. Perform the first inspection at 12,000 miles
(20 000 km) or 12 months.

24,000

40 000

Inspect the front suspension, tie rod ends and boot seals, replace if
necessary.

24,000

40 000

Replace the engine air cleaner filter.

30,000

50 000

MAINTENANCE SCHEDULES

447

T
E

N
A
N
C

S
C
H

D
U

L
E

Содержание 2008 Cherokee











































































































































































































































































































































































































































































































Результаты поиска

Содержание 2008 Cherokee

Отзывы:

Бренды по названию

Популярные бренды

Jeep 2008 Cherokee, Руководство пользователя

Результаты поиска

Содержание 2008 Cherokee

Отзывы:

Бренды по названию

Популярные бренды