Jeep 2008 Cherokee Скачать руководство пользователя страница 283 | Manualshive

Страница: 283 / 490

Jeep 2008 Cherokee Скачать руководство пользователя страница 283

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the heater
cord to a ground-fault interrupter protected 110-115 volt
AC electrical outlet with a grounded, three-wire exten-
sion cord.

Use the heater when temperatures below 0°F (-18°C) are
expected to last for several days.

The block heater must be plugged in at least one hour to
have an adequate warming effect on the coolant.

The engine block heater cord is located:

•

3.7L/4.7L Engine — coiled and strapped to the engine
oil dipstick tube.

•

5.7L Engine — bundled and fastened to the injector
harness.

•

3.0L Diesel Engine — on the passenger side of the
vehicle mounted on a stud between the fresh airbox
and coolant reservoir.

WARNING!

Remember to disconnect the cord before driving.
Damage to the 110-115 volt AC electrical cord could
cause electrocution.

STARTING AND OPERATING

283

5

«
...
281
282
283
284
285
...
»

Содержание 2008 Cherokee











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды