Jeep 2008 Cherokee Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 490

Jeep 2008 Cherokee Скачать руководство пользователя страница 130

section. For information on the rear wiper and washer,
refer to “Rear Window Features” in this section.

NOTE:

Always remove any build-up of snow that

prevents the windshield wiper blades from returning to
the OFF position. If the windshield wiper switch is

turned off and the blades cannot return to the OFF
position, damage to the wiper motor may occur.

To use the washer, pull the lever toward you and hold
while spray is desired. If the lever is pulled while in the
delay range, the wiper will operate for several seconds
after the lever is released, and then resume the intermit-
tent interval previously selected.

If the lever is pulled while in the OFF position, the wipers
will operate for several wipe cycles, then turn off.

WARNING!

Sudden loss of visibility through the windshield
could lead to an accident. You might not see other
vehicles or other obstacles. To avoid sudden icing of
the windshield during freezing weather, warm the
windshield with the defroster before and during
windshield washer use.

Windshield Wiper/Washer Switch

130

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
128
129
130
131
132
...
»

Содержание 2008 Cherokee











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды